manualshive.com logo in svg

Polaris ATV 2002, Руководство пользователя, Страница: 114 / 181

Поделиться
Скачать
Polaris ATV 2002 Скачать руководство пользователя страница 114

111

MAINTENANCE AND LUBRICATION

Lubrication

Oil Filter and Change

Magnum 325 2x4, Magnum 325 4x4, Trail Boss
Oil and Filter Change

1. Place vehicle on a

level surface.

2. Run engine two to

three minutes until

warm. Stop engine.

3. Clean area around

drain plug.

4. Place a drain pan

beneath engine

crankcase and

remove drain plug.

CAUTION:

Oil

may be hot. Do not

allow hot oil to come into contact with skin as serious burns may

result.

5. Allow oil to drain completely.

6. Replace sealing washer on drain plug.

NOTE:

The sealing

surfaces on drain plug and crankcase should be clean and free of

burrs, nicks or scratches.

7. Reinstall drain plug and torque to 14 ft. lbs. (19 Nm).
8. Place shop towels beneath oil filter. Using an oil filter wrench,

turn filter counterclockwise to remove.

9. Using a clean dry cloth, clean filter sealing surface on crankcase.
10. Lubricate O-ring on new filter with a film of engine oil. Check to

make sure the O-ring is in good condition.

11. Install new filter and turn by hand until filter gasket contacts the

sealing surface, then turn and additional 1/2 turn.

Crankcase Drain

Содержание ATV 2002






















































































































































































Отзывы:

Нет отзывов