Polaris ATV 2002 страница 110 Скачать руководство пользователя

Страница: 110 / 181

107

MAINTENANCE AND LUBRICATION

Lubrication

Oil Pump Adjustment Procedure - 250 Engines

1. Before adjusting the oil

pump, check engine idle

RPM and carburetor

adjustments which are found

in the owner’s manual

supplement.

2. Loosen throttle cable jam

nut (A) and turn adjuster in

or out until there is 1/16

″

1/8

″

(.16 - .32 cm) of

throttle lever travel before

throttle slide starts to open.

See Owner’s Manual

Supplement.

3. Place very slight pressure on

the throttle lever until all

freeplay is removed from

throttle cable (to the point

where the carb slide is just

starting to rise).

4. Loosen locknut. Turn

adjuster in or out until all

freeplay is removed from oil

pump cable (the point where

the oil pump arm is just

starting to move off of its

stop). The pump stop keeps

the pump arm from rotating

any farther down than the

idle position so no visual

alignment of marks is

necessary. Tighten the

locknut

Lever

Locknut

Cable Adjuster

Locknut

Lever Arm

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды