Polaris ATV 2002 страница 105 Скачать руководство пользователя

Страница: 105 / 181

102

MAINTENANCE AND LUBRICATION

Engine Cooling System

Radiator Coolant Level Inspection

NOTE:

This procedure is

only required if the cooling

system has been drained for

maintenance and/or repair.

However, if the recovery bottle

has run dry, the level in the

radiator should be inspected

and coolant added if necessary.
To access the radiator pressure

cap:

Gen III (A)

- To access the

pressure cap, clean the area

around the oil cap and remove

the oil cap (2-cycle models).

Remove front cover by placing

your fingers under the front of

the cover and pulling upward.

Reinstall oil cap.

Gen IV (B)

- Using the tool

provided, remove the four

screws securing front rack (2).

Remove front cover (3) by

placing your fingers under the

front of the cover and pulling

upward.

Never remove the pressure cap when the engine is warm or hot.

Escaping steam can cause severe burns. The engine must be

cool before removing the pressure cap.

WARNING

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды