Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 54

Страница: 54 / 456

2.34

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Connect and tighten the black (negative) cable last.

Verify that cables are properly routed and reinstall
the body panel above the footwell.

Spark Plug Service

Remove the driver’s seat and disconnect the (-)
negative battery cable from the battery.

WARNING

A hot exhaust system and engine can cause serious

burns. Allow engine to cool or wear protective gloves

when removing the spark plugs.

Clean top of engine to remove all dirt and debris.

Remove the spark plug wire from the engine.

NOTE: Image For Reference Only.

Remove spark plug.

Inspect electrodes for wear and carbon buildup. Look
for a sharp outer edge with no rounding or erosion of
the electrodes.

Clean with electrical contact cleaner only.

MAINTENANCE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды