Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 399

Страница: 399 / 456

10.19

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

SPEED SENSOR

Speed Sensor Location

The speed sensor is located on the RH transmission
case and can be accessed through the rear RH wheel
well area.

NOTE: Image For Reference Only.

Speed Sensor Testing

Special Tools Required:

Static Timing Light Harness (PN 2871745)

Hall Sensor Probe Harness (PN 2460761)

Disconnect the 3 wire harness from the speed
sensor

and

remove

the

sensor

from

the

transmission.

Connect the wires from the Static Timing Light
Harness to the sensor 3 pin connector using the Hall
Sensor Probe Harness (PN 2460761).

Pass a screwdriver back and forth in front of the
sensor tip.

Be sure connections are good and 9V battery is in
good condition. If the light flashes, the sensor is
good.

ELECTRICAL

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды