Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 456

background image

2.18

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Compression Test Specification

NOTE:

This engine does have decompression

components.

A smooth idle generally indicates good compression.
Low engine compression is rarely a factor in running
condition problems above idle speed.

Cylinder Compression:

80 - 120 psi (decompression)

Engine Mounts

Inspect rubber engine mounts for cracks or damage.
Check engine fasteners and ensure they are tight.

Valve Clearance Inspection

NOTE:

Valve

clearance

inspection

should

be

performed on a cold engine, at room temperature.

1.

Remove the seats and disconnect the negative (-)
battery cable.

2.

Remove the air box cover and PVT ducting tubes.
(Non-Touring models require fuel tank removal.

3.

Remove the spark plug wire from the engine and
remove the spark plug. Place a clean shop towel into
the spark plug tube to prevent debris from entering
the combustion chamber.

4.

Remove the (3) T40 bolts retaining the valve cover.

NOTE:

Discard valve cover Isolators upon

removal.

New

Isolators

are

required

once

removed.

Inspect the valve cover gasket and replace if
damaged or signs of leaking are present.

5.

Remove the valve cover from the engine.

6.

Remove the outer PVT cover and drive belt as shown
in chapter 6.

MAINTENANCE

«
...
36
37
38
39
40
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: MANCO Страницы: 8

Бренд: Landoll Страницы: 80

Бренд: Yamaha Страницы: 176

Бренд: XY Powersports Страницы: 259

Бренд: cectek Страницы: 125

Бренд: SQ Racing Страницы: 11

Бренд: Trail Rover Страницы: 38

Бренд: Jerr-Dan Страницы: 104

Бренд: Landoll Страницы: 72

2013 RANGER RZR 570

Бренд: Polaris Страницы: 152

Бренд: EBO Страницы: 19

Бренд: Can-Am Страницы: 423

Бренд: Coleman Powersports Страницы: 38

Venture Lite PZ50RTB

Бренд: Yamaha Страницы: 100

KODIAK YFM700FWBD 2017

Бренд: Yamaha Страницы: 176

KODIAK 700 YFM70KDXG

Бренд: Yamaha Страницы: 180

Бренд: Kärcher Страницы: 19

Бренд: Ultraflex Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды