Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 351 | Manualshive

Страница: 351 / 456

background image

9

9.7

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Brake Bleeding / Fluid Change

NOTE: When bleeding the brakes or replacing the
fluid, always start with the caliper farthest from the
master cylinder.

CAUTION

Always wear safety glasses during these procedures.

Brake fluid will damage finished surfaces. Do not allow

brake fluid to come in contact with finished surfaces.

NOTE: Do not remove brake lever when reservoir
fluid level is low.

This procedure should be used to change fluid or bleed
brakes during regular maintenance.

1.

Clean reservoir cover thoroughly.

2.

Remove screws, cover and diaphragm (C) from
reservoir.

3.

Inspect vent slots (A) in cover and remove any debris
or blockage.

4.

If changing fluid, remove old fluid from reservoir with
a Mity Vac® pump (

PN 2870975

) or similar tool.

5.

Begin bleeding procedure with the caliper that is
farthest from the master cylinder. Install a box end
wrench on caliper bleeder screw. Attach a clean,
clear hose to fitting and place the other end in a
clean container. Be sure the hose fits tightly on
fitting.

NOTE: Fluid may be forced from supply port (B)
when brake lever is pumped. Place diaphragm
(C) in reservoir to prevent spills. Do not install
cover. See Illustration above.

6.

Slowly pump the brake lever until pressure builds
and holds.

7.

While maintaining lever pressure, open bleeder
screw. Close bleeder screw and release brake lever.

NOTE:

Do not release lever before bleeder

screw is tight or air may be drawn into caliper.

8.

Repeat procedure until clean fluid appears in bleeder
hose and all air has been purged. Add fluid as
necessary to maintain level in reservoir.

CAUTION

Maintain at least 1/2", (1.27 cm) of brake fluid

in the reservoir to prevent air from

entering the master cylinder.

9.

Tighten bleeder screw securely and remove bleeder
hose. Torque the bleeder screw to specification.

Bleeder Screw:

25-30 in-lbs (2.80-3.40 Nm)

BRAKES

«
...
349
350
351
352
353
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: B.O.B Страницы: 36

MAVERICK Trail 2021 Series

Бренд: Can-Am Страницы: 195

Бренд: Suzuki Страницы: 624

FourTrax Foreman TRX500FE2 2018

Бренд: Honda Страницы: 279

Бренд: Honda Страницы: 229

Бренд: Honda Страницы: 159

Бренд: Honda Страницы: 71

Бренд: Yamaha Страницы: 17

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 156

BLASTER YFS200P

Бренд: Yamaha Страницы: 156

BLASTER YFS200N

Бренд: Yamaha Страницы: 153

Бренд: Yamaha Страницы: 153

Бренд: Yamaha Страницы: 155

BIG BEAR YFM400S

Бренд: Yamaha Страницы: 171

Бренд: Yamaha Страницы: 191

Бренд: Monzana Страницы: 13

Бренд: Miller Electric Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды