Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 456

background image

2.12

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Throttle Inspection

Check for smooth throttle opening and closing in all
handlebar positions. Throttle lever operation should be
smooth and lever must return freely without binding.

1.

Place the gear selector in Park.

2.

Set parking brake.

3.

Start the engine and let it idle.

4.

Turn handlebars from full right to full left. If idle speed
increases at any point in the turning range, inspect
throttle cable routing and condition. Adjust cable
tension as needed until lock-to-lock turning can be
accomplished with no rise in engine rpm.

5.

Replace the throttle cable if worn, kinked, or
damaged.

To remove the TRS cover:

6.

Use a medium flat blade screwdriver and insert
blade into the pocket of the cover starting on the #1
position.

7.

Twist screwdriver slightly while lifting on the cover to
release snap.

8.

Repeat procedure at the other five locations as
shown.

NOTE: Do not attempt to remove cover until all
latch points are released.

Throttle Cable / Throttle Release System
(TRS Switch) Adjustment

1.

Slide boot off throttle cable adjuster and jam nut.

2.

Place shift selector in neutral and set parking brake.

3.

Loosen lock nut on in-line cable adjuster (Ill. 1).

4.

Turn adjuster until specified freeplay is achieved at
thumb

lever.

(see

illustration).

After

making

adjustments, quickly actuate the thumb lever several
times and reverify freeplay.

Throttle Freeplay:

.0625 - .1250" (1.58 - 3.17mm)

5.

Tighten lock nut securely and slide boot completely
in place to ensure a water-resistant seal.

6.

Turn handlebars from left to right through the entire
turning range. If idle speed increases, check for
proper cable routing. If cable is routed properly and
in good condition, repeat adjustment procedure

MAINTENANCE

«
...
30
31
32
33
34
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Joyner Страницы: 40

MINITRANSPORTER MECH 35

Бренд: Fort Страницы: 64

Бренд: Meec tools Страницы: 56

Бренд: E-Z-GO Страницы: 192

WILD HP 450 - 2005

Бренд: GAS GAS Страницы: 71

Бренд: Daymak Страницы: 28

Бренд: North Star Страницы: 16

Cushman HAULER 800X ELiTE 2019

Бренд: Textron Specialized Vehicles Страницы: 66

Бренд: Ammann Страницы: 170

Бренд: Sodi Страницы: 7

Бренд: Sodi Страницы: 28

Бренд: Sodi Страницы: 34

Бренд: Sodi Страницы: 37

Бренд: Coleman Powersports Страницы: 78

2005 FOURTRAX RANCHER AT TRX400FA

Бренд: Honda Страницы: 286

2005 TRX90 Sportrax

Бренд: Honda Страницы: 207

2001 TRX 250 Fourtrax Recon

Бренд: Honda Страницы: 154

2001 TRX400EX Sportrax 400EX

Бренд: Honda Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды