Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 280 | Manualshive

Страница: 280 / 456

background image

6.46

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

TROUBLESHOOTING

SITUATION

PROBABLE CAUSE

REMEDY

Engine RPM
below specified
operating range,
although engine
is properly tuned.

-Wrong or broken drive clutch spring.

-Drive clutch shift weight too heavy.

-Driven clutch spring broken or installed in
wrong helix location.

-Replace with recommended spring.

-Install correct shift weight kit to match engine
application.

-Replace spring; refer to proper installation
location.

Erratic engine
operating RPM
during
acceleration or
load variations.

-Drive clutch binding.

-Belt worn unevenly - thin / burnt spots.

-Driven clutch malfunction.

-Sheave face grooved.

A. Disassemble drive clutch; inspect shift
weights for wear and free operation.
B. Clean and polish stationary shaft hub;
reassemble clutch without spring to determine
problem area.

-Replace belt.

A. Replace ramp buttons.
B. Inspect movable sheave for excessive
bushing clearance.

-Replace the clutch.

Engine RPM
above specified
operating range.

-Incorrect drive clutch spring (too high spring
rate).
-Drive clutch shift weights incorrect for
application (too light).
-Drive clutch binding.

-Driven clutch binding.

-Converter sheaves greasy; belt slipage.

-Install correct recommended spring.

-Install correct recommended shift weights.

-Disassemble and clean clutch, inspecting shift
weights and rollers. Reassemble without the
spring and move sheaves through entire range
to further determine probable cause.

-Disassemble, clean, and inspect driven clutch,
noting worn sheave bushing and ramp buttons
and helix spring location.

-Clean sheaves with denatured alcohol or brake
cleaner, install new belt.

Harsh drive clutch
engagement.

-Drive belt worn too narrow.

-Excessive belt / sheave clearance with new
belt.

-Replace belt.

-Perform belt / sheave clearance adjustment
with shim washers beneath spider.

Drive belt turns
over

-Wrong belt for application.
-Clutch alignment out of spec.
-Engine mount broken or loose.

-Replace with correct belt.
-Adjust clutch alignment.
-Inspect / adjust or replace.

Belt burnt, thin
spots

-Abuse (continued throttle application when
vehicle is stationary, excess load)

-Dragging brake

-Slow, easy clutch engagement

-Caution operator to operate machine within
guidelines.

-Vehicle operated with park brake on. Inspect
brake system.

-Fast, effective use of throttle for efficient
engagement.

CLUTCHING

«
...
278
279
280
281
282
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Linhai Страницы: 208

Бренд: Taylor-Dunn Страницы: 166

RS Venture RST90A

Бренд: Yamaha Страницы: 140

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 127

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 163

Бренд: Yamaha Страницы: 142

Raptor YFM7RSEZ

Бренд: Yamaha Страницы: 154

Бренд: Yamaha Страницы: 146

Бренд: Yamaha Страницы: 158

Бренд: Yamaha Страницы: 176

Raptor 700R YFM70RSPX

Бренд: Yamaha Страницы: 158

Raptor 700R YFM70RSEW

Бренд: Yamaha Страницы: 158

Raptor 250 YFM25RX

Бренд: Yamaha Страницы: 148

Бренд: Yamaha Страницы: 162

Raptor YFM660RT

Бренд: Yamaha Страницы: 186

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды