Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 263

Страница: 263 / 456

6.29

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Clutch Disassembly / Inspection

Place

the

clutch

into

the

Universal

Clutch

Compressor Tool

PU-50518

. Press down on the top

of the spider assembly, pushing the spider onto the
shaft. Remove snap ring and slowly release the
assembly.

CAUTION

Wear eye protection when removing snap ring to

prevent serious personal injury.

Remove snap ring retainer.

Note the location of the spring and remove helix.

Note the location of the spring in the moveable
sheave, and remove the spring.

Check alignment of tabs on spring. Replace the
spring if tabs are misaligned or the spring coils are
distorted.

Inspect ramp buttons in the moveable sheave and
replace if worn.

NOTE: The ramp buttons are secured by Torx™
screws (T20).

CLUTCHING

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды