Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 456

background image

6.14

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Belt Deflection (Tension) (NON EBS ONLY)

Belt Deflection (Tension):

Maximum 1 1/8” (2.9 cm)

Pinch the sheaves lightly together with clamp to prevent
the belt from being pushed into the driven sheave.

1.

Place a straight edge on top of the belt between
drive and driven clutch.

2.

Push down on drive belt until it is lightly tensioned.

3.

Measure belt deflection as shown in the image
above.

If belt deflection is out of specification, adjust by
removing or adding shims between the driven clutch
sheaves.

• Remove shims to decrease belt deflection

• Add shims to increase belt deflection

Refer to “Driven Clutch Service” section.

At least one shim must remain between the inner
and outer sheave of the driven clutch. If proper belt
deflection cannot be obtained, measure drive belt
width, length, and center distance of drive and driven
clutch, outlined in this section; all have an effect on
belt deflection.

Setting Center-To-Center Distance

Clutch center distance is controlled by the correct
positioning of the engine and transmission mounting.
The 10” Center Distance Tool (PN 2871710) should be
used for the following:

• After engine installation.

• After transmission installation.

• After engine or transmission mount replacement.

• If the vehicle exhibits drive clutch drag or hard

shifting while at idle speed, after clutch offset
adjustment has been performed.

CLUTCHING

«
...
246
247
248
249
250
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: UtilityDump Страницы: 13

1997 Fourtrax TRX250

Бренд: Honda Страницы: 155

Бренд: Komatsu Страницы: 435

Hawkeye 2X4 2007

Бренд: Polaris Страницы: 141

Бренд: Polaris Страницы: 133

RANGER 500 2017

Бренд: Polaris Страницы: 574

2010 Scrambler 4X4

Бренд: Polaris Страницы: 133

Sportsman BIG BOSS 6X6 800 EFI

Бренд: Polaris Страницы: 100

Бренд: HTI Страницы: 6

Бренд: Egholm Страницы: 16

Бренд: Ultra-tow Страницы: 9

Бренд: Erde Страницы: 4

Бренд: Har-Tru Страницы: 12

Бренд: Cannondale Страницы: 180

Dump Series D5TLP

Бренд: Anderson Manufacturing Страницы: 1

Sodi Racing Furia 950

Бренд: Sodikart Страницы: 36

Бренд: SSR Страницы: 16

Go-kart JNSZ650DS

Бренд: Joyner Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды