Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 152

Страница: 152 / 456

4.6

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

EFI System Component Locations

Electronic Control Unit (ECU)

-Located under the

front cover (under the front rack).

Temperature and Manifold Absolute Pressure
Sensor (T-MAP)

- Located in the rubber intake boot

between the throttle body and the cylinder head.

Crankshaft Position Sensor (CPS)

- Located in the

magneto cover on the right-hand side of the Engine.

Fuel Injectors / Fuel Rail / Regulator

- Attached to

the fuel rail located in the intake track of the cylinder
head.

Fuel Pump / Regulator / Fuel Gauge Sender
Assembly

- Located in/on the fuel tank under the

front cab.

FUEL SYSTEM - GENERAL

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды