Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 456

background image

3

3.71

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

5.

Fully install the Freewheel gear (starter gear) onto
the crankshaft as shown.

6.

Align the flywheel keyway with flywheel key on the
crankshaft.

7.

By hand, lightly press the flywheel inward while
rotating the freewheel gear counter clock-wise. Fully
install the flywheel until seated on the crankshaft
taper.

8.

Install the flywheel washer.

9.

Hold flywheel with commercially available strap
wrench.

10. Torque

new

flywheel nut (3) to specification.

Flywheel Retaining Nut:

133 ft-lbs (180 Nm)

11. Install starter idler gear and shaft (4).

Stator Removal

NOTE: Test stator wire continuity before removing it
from the housing.

1.

Remove the stator cover as outlined in the ”Water
Pump Mechanical Seal / Oil Seal Replacement”
procedure” in this chapter.

CAUTION

The flywheel contains powerful magnets. Use caution

when removing the stator cover.

DO NOT place fingers between cover and crankcase at

any time during the removal process or injury could

result.

2.

Remove and discard the stator cover gasket.

CAUTION

Be sure engine coolant does not contaminate the

engine oil during stator cover service.

3.

Remove the 3 bolts (C) that secure the stator to the
stator cover.

4.

Remove the 2 bolts that secure the stator wire
routing bracket (D) to the stator cover.

5.

Remove the stator (E) from the stator cover.

Stator / Stator Cover Installation

1.

Clean and degrease screws and threads in stator
housing.

2.

Clean mounting surfaces of stator and housing.

ENGINE

«
...
127
128
129
130
131
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Landoll Страницы: 86

1995 Fourtrax 300

Бренд: Honda Страницы: 156

Бренд: Algema Страницы: 108

Twister UM250IIR

Бренд: Hammerhead Страницы: 67

PAVER SPECIAL RPS Series

Бренд: Etnyre Страницы: 61

Бренд: FLEMING Страницы: 6

Бренд: Ardisam Страницы: 10

Бренд: Turftime Страницы: 24

Бренд: Xxxlutz Страницы: 58

Бренд: X-TREME Страницы: 26

Бренд: Fisher-Price Страницы: 40

Sportsman 850 Touring EPS

Бренд: Polaris Страницы: 510

Бренд: LJ'S TOPS & BOTTOMS Страницы: 14

Бренд: Aero Страницы: 32

Бренд: Baja Страницы: 55

Бренд: Yamaha Страницы: 108

INTIMIDATOR XD 4

Бренд: DFK Страницы: 84

Бренд: Yamaha Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды