Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 456

background image

3.68

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

ENGINE DISASSEMBLY / INSPECTION - LOWER END

Crankcase Disassembly

NOTE: The engine top end, starter motor, stator
cover, starter drive, flywheel, stator, cam chain, oil
pump and sprockets can be serviced with the engine
installed in the vehicle.

Flywheel / Stator Housing Removal

1.

Remove the stator cover as outlined in the ”Water
Pump Mechanical Seal / Oil Seal Replacement”
procedure” in this chapter.

CAUTION

The flywheel contains powerful magnets. Use caution

when removing the stator cover.

DO NOT place fingers between cover and crankcase at

any time during the removal process or injury could

result.

CAUTION

Be sure engine coolant does not contaminate the

engine oil during stator cover service.

2.

Remove starter drive gear and shaft(4). Inspect gear
teeth for damage. Inspect fit of shaft inside gear and
replace gear assembly if clearance is excessive.
Inspect shaft and shaft bearing surfaces in case and
stator housing for wear.

3.

Hold flywheel with a commercially available strap
wrench and remove flywheel nut and washer.
Discard the flywheel nut and replace for assembly.

NOTE: The flywheel nut has standard rotation
(right hand) threads.

4.

Back the center screw of flywheel puller PA-49316
completely out and screw puller onto flywheel
completely.

5.

Tighten center bolt of tool PA-49316 and remove
flywheel.

Starter One-Way Clutch Inspection

1.

Remove flywheel as outlined in this chapter.

2.

Place flywheel on work bench. Grasp gear and rotate
clockwise. It should turn smoothly without binding.

3.

Rotate gear counterclockwise. The gear should
immediately lock in position and not slip.

4.

Inspect inside of hub (A) for wear, galling, or uneven
surface.

ENGINE

«
...
124
125
126
127
128
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Team Durango Страницы: 32

Бренд: Odes Industry Страницы: 73

Бренд: Honda Страницы: 250

Бренд: CadKat Страницы: 11

120 Sno Pro 2010

Бренд: Arctic Cat Страницы: 562

Бренд: Suzuki Страницы: 215

MKII 600 Series

Бренд: NC ENGINEERING Страницы: 80

Renegade 570 2016

Бренд: Can-Am Страницы: 534

Бренд: Yamaha Страницы: 841

Бренд: Yamaha Страницы: 293

YXZ 1000R SS 2022

Бренд: Yamaha Страницы: 216

GRIZZLY 350 YFM35FGD

Бренд: Yamaha Страницы: 144

Бренд: E-TON Страницы: 225

Sportsman BIG BOSS 6x6

Бренд: Polaris Страницы: 141

Dump Series DG7Ton

Бренд: Anderson Manufacturing Страницы: 1

Бренд: Shop fox Страницы: 2

Бренд: TGB Страницы: 86

Бренд: ROSSO MOTORS Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды