PMD Atlas Compact Скачать руководство пользователя страница 135

Страница: 135 / 188

Atlas® Digital Amplifier Complete Technical Reference

135

SetDriveCommandMode

7Eh

GetDriveCommandMode

7Fh

Syntax

SetDriveCommandMode

mode

GetDriveCommandMode

Arguments

Name

Instance

Encoding

format

BLDC

Step

transport

SPI

Pulse and Direction

Packet

Structure

Description

SetDriveCommandMode

may be used to change the means of commanding Atlas motor torque. The

transport field specifies the physical interface used for torque commands, either the default Serial
Peripheral Interface, or Pulse and Direction. See

Section 4.9.1, “Pulse & Direction Signal Input Mode”

for

more information on pulse and direction mode.

The format field specifies the layout of the torque command; in the Atlas only one format is supported
for each motor type. See

Section 5.3, “Sending a Voltage or Torque Output Value”

for details.

The format for pulse and direction input must be Step.

SetDriveCommand mode

write

checksum

8 7

write

transport

format

GetDriveCommand mode

write

checksum

8 7

write

transport

format

Содержание Atlas Compact





























































































































































































Результаты поиска

Содержание Atlas Compact

Отзывы:

Бренды по названию

Популярные бренды

PMD Atlas Compact, Полное техническое руководство

Результаты поиска

Содержание Atlas Compact

Отзывы:

Бренды по названию

Популярные бренды