background image

 

7

 

Operating the regulator 

This  section  briefly  describes  how  the 
regulator should be operated.  

7.1

 

Description of buttons and display  

 

 

Drawing 1. Keyboard view,  

Legend: 
1.

 

menu item change button 

2.

 

STOP button, value decrease 

3.

 

START button, value increase 

4.

 

mains switch 

5.

 

fuse socket 

After  turning  the  regulator  on,  the  START 
and  STOP  buttons  are  used  to  enable  and 
disable airflow respectively. 

 

 

 

 

Drawing 2. Main display window 

Legend: 
1.

 

preset boiler or hot utility water tank 
temperature, or preset temperature of 
emission,  

2.

 

measured temperature of boiler, hot 
utility water tank, or emission, 

3.

 

signal arrow 

4.

 

SUMMER – hot utility water mode symbol  

5.

 

PRIORITY - hot utility water mode symbol 

6.

 

Boiler regulation mode – PID function, 

7.

 

Room thermostat - this symbol lights up 
when the temperature inside the room 
reaches the preset value contacts are 
disconnected) 

8.

 

alarm symbol 

9.

 

signal of increasing the preset boiler 
temperature due to hot utility water 
heating, 

10.

 

signal decreasing the preset boiler 
temperature due to operation of the room 
thermostat, 

11.

 

service menu symbol 

12.

 

hot utility water temperature sensor, 

13.

 

central heating pump symbol 

14.

 

hot utility water pump symbol 

15.

 

boiler temperature sensor, 

16.

 

emission temperature sensor,  

17.

 

airflow power 

18.

 

fan  symbol  it  this  is  not  visible  – 
regulation  is  off,  it  is  visible  –  regulation 
is on, if it flashes – the regulator is in the 
SUPERVISION mode 

19.

 

hot utility water tank symbol 

20.

 

icons: 

 

Temperature settings 

 

Blow-off time 

 

Blow-off interval 

  Maximum revolutions 

  Minimum revolutions 

 

Settings for hot utility water 

 

Boiler regulation mode 

 

Service menu symbol 

7.2

 

First start-up of the regulator 

Before  the  first  start-up  of  the  regulator,  it 
should  be  programmed  for  the  purposes  of 
cooperation with the given boiler and heating 
system,  in  accordance  with  point  11.9.  It  is 
recommended  that  this  performed  by  a 
person familiar with heating technology. 

7.3

 

Start-up of the regulator 

10 

9  8 

6  5 

11 

14 

12

15 

13 

16 

19 

17 

18 

Содержание ecoMAX 200 W




























Отзывы: