pleasant hearth PH35PS-B Скачать руководство пользователя страница 13

Страница: 13 / 44

[email protected]

7077-801F • 08/20

Cleaning or Inspection

Frequency

Daily

Weekly Monthly Yearly

Firepot

Every 3 bags of fuel

Ash Removal from Firebox

Every 5 bags of fuel or more frequently

depending on ash build-up

Glass

When clear view of firepot becomes obscure OR

Hopper

Every 25 bags of fuel

Exhaust Path, Drop Tube and

Behind Baffles

Every 25 bags or more frequently

depending on ash build-up

Door Handle & Gasket Inspection

Prior to heating season

Blower, Convection

Every 25 bags or more frequently

depending on operating environment.

Blower, Exhaust

More frequently depending on the fuel type OR

Firebox - Prepare for Non-Burn

Season

At end of heating season

Venting System

Every 3 tons or more frequently depending

on the fuel type

B. Quick Reference Maintenance Chart

Follow the detailed instructions found in this section for each step listed as referenced in the

chart below.

NOTICE:

These are recommendations. Clean more frequently if you encounter heavy build-up of ash at the

recommended interval or you see soot coming from the vent.

Not properly cleaning your appliance on a

regular basis will void your warranty.

When properly maintained, your appliance will give you

many years of trouble-free service. Contact your GHP

dealer to answer questions regarding proper operation,

troubleshooting and service for your appliance.

A. Proper Shutdown Procedure

Turn dial control to off, let appliance completely cool and

exhaust blower must be off. After cooling unplug appliance

before servicing.

Maintaining & Servicing Your Appliance

Shock and Smoke Hazard

•

Smoke spillage into room can occur if

appliance is not cool before unplugging.

•

Risk of shock if appliance not unplugged

before servicing appliance.

CAUTION

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды