manualshive.com logo in svg

Plasma IBEAM FC, Руководство пользователя, Страница: 43 / 60

Поделиться
Скачать
Plasma IBEAM FC Скачать руководство пользователя страница 43

 

 

40 

Section 5.2: Command Details

 

 

Serial command:  

A

 

Description:   Attention and put IBEAM in REMOTE mode. 
Usage:  

A<cr> 

Example:  

Send  “A<cr>”.    The  IBEAM  will  switch  to  REMOTE  mode  (if  not  already  in 
REMOTE mode). 

Response: 

<lf><cr>OK<lf><cr><eot> 

 

 

Serial command:  

AB

 

Description:   Set the accelerator to beam (A/B) ratio. 
Usage:  

AB(0-99)<cr> 

Example:  

Send  “AB10<cr>”.    The  A/B  ratio  will  be  set  to  10%.    If  the  accelerator  current 
exceeds  10%  of  the  beam  current,  an  error  will  be  displayed.   Acceptable  range  is 

from 0 to 99%.  Default is 10. 

 Response: 

<lf><cr>OK<lf><cr><eot> 

 
 
Serial command:  

AC

 

Description:   Enable Auto Cathode Mode (in Remote mode). When enabled, the cathode filament 

current  will  increase  automatically  until  one  of  two  conditions  are  met;  either  the 

cathode current limit, or the discharge current threshold setting. 

Usage:  

AC(0 or 1)<cr> 

Example:  

Send “AC1<cr>”.  Auto Cathode mode will be enabled. Sending “AC0<cr>” will 
disable Auto Cathode mode. 

 Response: 

<lf><cr>OK<lf><cr><eot> 

 

 

Serial command:  

AV

 

Description:   Set the accelerator voltage. 
Usage:  

AV(0-1000)<cr> 

Example:  

Send “AV250<cr>”.  The accelerator voltage will be set to 250 V.  Acceptable range 
is from 0 to 1000 V.  Below 100 V is not recommended. 

 Response: 

<lf><cr>OK<lf><cr><eot> 

 
 

 

Содержание IBEAM FC





























































Отзывы:

Нет отзывов