Planmeca Compact i3 Скачать руководство пользователя страница 84

Страница: 84 / 106

15 Attaching tray table assembly to OP delivery arm

balanced arm instrument console

The mounting arm is attached to the instrument console by pushing it to its

position.
The friction of the tray arm movements can be adjusted. Loosen the joint

attachment screw using a 3 mm Allen key (1). Rotate the plate manually and

move the tray arm (2). Hold the plate in position with pliers (3) and tighten

the attachment screw (4).
The angle of the tray table can be adjusted as follows. Loosen the securing

screws (5) and adjust the angle (7) with four adjustment screws (6). Tighten

the securing screws.

15 Attaching tray table assembly to OP delivery arm balanced arm instrument console

80 Planmeca Compact i3

Installation manual

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды