background image

Copyright Planika Sp. z o.o.  

www.planikafires.com 

 

IG0033#08 

2020-03-20 

 

 

1x complete Galio Corten gas fireplace 

 

1x remote control 

 

4x Tempered glass guards 

 

1x Touch panel (installed) 

 

4x AA Batteries  

 

2x AAA Batteries  

 

4x bag of decorative stones 

 

1x AS/NZS 1869 hose assembly – installed (only LPG version) 

 

1x pressure regulator– installed (only LPG version) 

 

1x installation manual and user’s manual 

 

 

3.2.

 

Unboxing and installation 

 

The contents of the boxes need to be carefully unwrapped from the foam foil. 

 

Remove the bags with decorative stones from the burner reservoir and place them away from it. 

 

Remove the Styrofoam placed on the unit. 

 

Carefully lift the appliance and pull out the glass shield wrapped in cardboard from the inside of the GaLiO 
Corten. 

 

Check the completeness of the elements with the contents list. 

 

Make sure that the device nor its elements weren’t damaged during the transportation (if they were, notify 
the supplier). 

 

Place GaLiO Corten on a flat, paved surface outside of the building, preferably on the place of final installation. 
Leave sufficient space on the side of the appliance where control panel is located (minimum 1 m). 

 

The decorative stones are to be scattered evenly around the reservoir to completely cover the burner of the 
fireplace. 

 

 

WARNING!!!

 

The stones may not cover or be placed inside the device protecting the ignition unit (Photo 1). 

 

It is forbidden to place any other decorative stones which are not supplied by the manufacturer. 

 

 

Delivered stones (Silicon Carbide – SiC, content 85%-95%).

 

 

Photo 1 

 

Carefully install the primary glass guards (See point 3.3). 

 

In the case of GaLiO Corten powered with natural gas, to obtain the optimum image of the flame, cover the 
burner with a single layer of decorative stones leaving some spaces uncovered of approximately every 10 cm 
(Photo 2). 

Содержание GaLiO Corten










































Отзывы: