Planika GaLiO Corten Скачать руководство пользователя страница 30

Страница: 30 / 41

www.planikafires.com

IG0033#08

2020-03-20

TROUBLESHOOTING

Warning! Installation, upkeep and service need to be conducted by a qualified professional with
appropriate qualification, an appropriate company or the gas supplier.

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

SMELL OF GAS

CLOSE THE VALVE ON THE GAS CYLINDER IMMEDIATELY. DO NOT USE

THE DEVICE UNTIL LEAKS HAVE BEEN REMOVED.

Leak detected at cylinder,

regulator or other

connection.

1. A loose regulator linkage.

2. Leak in the gas linkage, in the

regulator or on the gas knobs.

1. Tighten and test it.

2. Report this issue to service.

Burner does not ignite

1. The bottle is empty.

2. Igniter linkage is not connected.

3. No ignition spark.

4. The igniter electrode is placed

incorrectly opposite the igniter.

5. Gas nozzles are blocked.

6. Gas linkage is twisted.

7. Pressure regulator link is loose.

1. Replace Gas Cylinder.

2. Connect the igniter linkage.

3. Replace igniter.

4. Realign electrode and clear any

surrounding debris from area.

5. Unmount burner, clean the nozzle.

6. Straighten the linkage. Keep the

linkage away from the housing.

7. Tighten the link. Check for leaks.

Igniter Not Working

1. Ignitor wire not connected.

2. Electrode misaligned on pilot

burner

3. Igniter malfunction

1. Ensure pilot electrode wire is

connected.

2. Realign electrode and clear any

surrounding debris from area.

3. Replace Igniter

Low efficiency, „cracking”

sounds

1. The bottle is empty.

2. The nozzles of the burner are

blocked.

1. Replace Gas Cylinder.

2. Unmount the burner, clean the

nozzle.

Thumping sounds made

by the regulator.

The cylinder valve has opened

rapidly.

Unfasten the bottle valve slowly.

A vivid/ bright orange and

smoky flame of the

burner.

Holes blocked in the apparatus

producing the gas and air mixture.

Unmount the burner and clean/

unblock the apparatus’ holes.

Содержание GaLiO Corten










































Результаты поиска

Содержание GaLiO Corten

Отзывы:

Похожие инструкции для GaLiO Corten

Бренды по названию

Популярные бренды

Planika GaLiO Corten, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GaLiO Corten

Отзывы:

Похожие инструкции для GaLiO Corten

Бренды по названию

Популярные бренды