- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 8-Port 10/100/1000T
Wall-mounted Gigabit Ethernet Switch, WGS-803.
Open the box of the WGS-803 Gigabit Ethernet Switch
and carefully unpack it. The box should contain the
following items:
z
The WGS-803 Gigabit Ethernet Switch x 1
z
User Manual x 1
z
DIN-rail Kit x 1
z
Wall-mounted Kit x 1
z
Magnet Kit x 1
z
3-pin Terminal Block Connector x 1
z
RJ45 Dust-proof Cap x 8
If any item is found missing or damaged, please contact
your local reseller for replacement.
2.1 Terminal Block Connector Pinouts
To install the 3-pin Terminal Block Connector on the
WGS-803, simply follow the following steps:
Step 1:
Insert positive DC power wire into
V+
,
negative DC power wire into
V-
, and grounding
wire into
Ground
.
V+
V
-
Ground
Step 2:
Tighten the wire-clamp screws for preventing
the wires from loosening and plug into the
wall-mounted switch.
Note
1.
The wire gauge should be in the range
from 12 to 24 AWG
2. The device must be grounded
3. The DC power input range is 12V ~ 48V DC
2.2 LED Indicators
System
LED
Color
Function
PWR
Green
Lights
to indicate that the Switch has
power.
2.4 Physical Dimensions (WxDxH):
148 x 24.2 x 134mm
118.00
118.00
148.00
24.20
6.00
133.00
134.00
Dimensions ( unit = mm )
V+
V
-
Ground
2.3 Product Specifications
Model
WGS-803
Hardware Specifications
Network
Connector
8-port RJ45 for 10/100/1000BASE-T
MAC Address
Table
8K MAC address table with auto
learning function
Data Buffer
64Kbytes
Switch Fabric
16Gbps
Switch
Throughput
11.9Mpps@64bytes
Flow Control
Back pressure for half duplex. IEEE
802.3x pause frame for full duplex
Power
Requirements
12~48V DC, 0.5A (max.)
Power
Consumption
6 watts/20BTU
ESD Protection 6KV DC
EFT Protection
6KV DC
Enclosure
IP30 aluminum
2. Hardware Description
The front panel of the WGS-803 Gigabit Ethernet Switch
consists of 8 Auto-sensing 10/100/1000Mbps Ethernet
RJ45 Ports. The LED Indicators are also located on the
RJ45 ports of the Gigabit Ethernet Switch.
10/100/1000BASE-T RJ45 Port
10/100/1000BASE-T RJ45 Port
3-pin Terminal Block
DC Plug-in
10/100/1000BASE-T Interfaces
LED
Color
Function
LNK/
ACT
Green
Lights
To indicate the link through
that port is successfully
established.
Blinks
To indicate that the switch is
actively sending or receiving
data over that port.
1000 Green
Lights
To indicate that the port is
operating at
1000Mbps.
Off
If LNK/ACT LED is lit, it
indicates that the port is
operating at
10/100Mbps.
If LNK/ACT LED is Off, it
indicates that the port is link-
down.
3. Installation
3.1 Wall Mount Installation
To install the WGS-803 Gigabit Ethernet Switch on the
wall, simply follow the following steps:
Step 1:
There are 4 holes with 8mm diameter on
the wall; the distance between the 2 holes is
133mm and the line through them must be
horizontal.
Step 2:
Install a conductor pipe inside the board hole
and flush the edge of the conductor pipe with
the wall surface.
Step 3:
Screw the bolts into the conductor pipe. The
WGS-803 is between bolts and conductor pipe,
as shown below.
Dimensions
(W x D x H)
148 x 24.2 x 134 mm
Weight
498g
Standard Conformance
Standard
Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3x
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Regulatory
Compliance
FCC Part 15 Class A, CE
Environment
Operating
Temperature: -10 ~ 60 degrees C
Relative Humidity: 5 ~ 95%
(non-condensing)
Storage
Temperature: -20 ~ 70 degrees C
Relative Humidity: 5 ~ 95%
(non-condensing)