background image

1. Package Contents

Note

– 1 –

– 2 –

– 3 –

– 4 –

– 7 –

– 8 –

– 5 –

– 6 –

LED Indication

FURTHER INFORMATION:

The above steps introduce the simple installations and configurations of the 

WDAP-8350. For further configurations, please refer to the user manual, which 

can be downloaded from the website.

http://www.planet.com.tw/en/support/download.php?type1=4&model=4875

9&type=3

If you have further questions, please contact the local dealer or distributor 

where you purchased this product.

2011-E10630-000

Thank you for choosing PLANET WDAP-8350. Before installing the AP, please 

verify the contents inside the package box.

If there is any item missing or damaged, please contact the 

seller immediately.

Step 1:  Install the backplane at the rear of WDAP-8350 and screw the 4 

short screws with a Phillips screwdriver. Make the long screw rod 

pass through the holes of the backplane and put the flat pad, 

spring shim and the screw nut on it in proper order; do not lock 

it tight.

1. Click  the  “Start” button located in the lower-left corner of your 

computer.

2. Click “Control Panel”.
3.  Double-click the “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select  “Internet Protocol Version 4 (TCP/IPv4)” and click 

“Properties”.

7. Select “Use the following IP address” and then click the “OK” 

button twice to save the configuration. For example, you may choose 

from 192.168.1.1 to 192.168.1.254 excluding the default IP address of 

the WDAP-8350 (192.168.1.10).

Step 1: The Web management allows you to access and manage the 

wireless AP easily. Launch the Web browser and enter the default 

IP address http://192.168.1.10.  

Default IP Address: 192.168.1.10
Default User Name: admin
Default Password: admin
Default 2.4GHz SSID: PLANET_AP_2G
Default 5GHz SSID: PLANET_AP_5G

Step 3:  After you enter into the Web User Interface, click Wireless 

Settings at the left hand side of the screen to configure the 

wireless connection. Once the basic configuration of the AP is 

done. Click the Update button to make the change take effect.

Connect the WDAP-8350 with your PC via an Ethernet cable plugged into 

LAN port of PoE switch on one end and into LAN port of PC on the other 

end. Power on the WDAP-8350 via PoE from PoE switch.

WDAP-8350

Quick Installation Guide

600Mbps 802.11n Dual Band  Outdoor 

Wireless CPE

Stainless Tight Hoop Strip

Step 2:  When the login window appears, please enter the User Name and 

the Password. The default User Name and Password are both 

“admin”. Then click the Login button to continue.

For security reasons, it is recommended to change the password at the 

first login and memorize it.

Step 2:  Lock the 2 stainless tight hoop strips around the pole by passing 

through the mounting bracket and lock the fastening screws. 

Quick Guide

Backplane & Mounting Bracket

Mounting Kit

RJ45 Waterproof Kit

Step 3:  Install the device with the backplane to the mounting bracket on 

the column and fix the device and mounting bracket together by 

using 4 hex cap screws.  

Step 1:  As shown in Step 3-1, install the backplane at the rear of the 

WDAP-8350 first. Then, mark each point in the bracket for the 

screws. Remove the bracket to drill the points and insert the 

plastic wall-mounts. Use screws to lock the bracket with a 

screwdriver.

Step 2:  Assemble the device with the mounting bracket on the wall by 

using 4 short screws and 1 long screw.

WDAP-8350

x 2

N-Type (Male) to 

N-Type (Male) RF cable

5GHz Antenna with

N-Type (F) connector

2.4GHz Antenna with

N-Type (M) connector

Data

 + 

Power

Waterproof Kit

802.3at PoE Switch

Step 2:  Plug the RJ45 Ethernet cable into the PoE port of the WDAP-8350 

through the waterproof kit, and plug the other side of the RJ45  

cable into the PoE port of the PoE switch to finish the installation.

Step 1:  You can directly connect the antenna to the AP if the antenna’s 

connector is N-Type (M). If not, please connect the N-Type 

(M) RF cables to N-Type (F) antenna connectors of the 

WDAP-8350, and connect the other end of the RF cables to the 

N-Type (F) antennas.

5GHz WLAN LED
2.4GHz WLAN LED

Power LED

Ground Lug

LAN LED

Connector and Port  

PoE LAN Port

Ground Terminal

Reset Button

5GHz N-Type (Female)

Antenna Connectors

2.4GHz N-Type (Female)

Antenna Connectors

IMPORTANT SAFETY PRECAUTIONS:

1)  LIVES MAY BE AT RISK! Please be aware of the electrical 

wires around. Carefully read the section "OUTDOOR 

INSTALLATION WARNING" in the manual before 

installation.

2) Users  MUST complete grounding wired with the 

WDAP-8350; otherwise, a sudden lightning could cause 

fatal damage to the WDAP-8350. EMD (Lightning) 

DAMAGE IS NOT COVERED UNDER WARRANTY.

Caution

4. Wall Mounting Installation

 The actual antenna 

connection depends 
on the antenna type 
you choose. The 
antennas are 
required and must 
be purchased 
separately.

 Please remember to 

install the ground 
cables onto the 
ground terminal and 
ground lugs.

3. Pole Mounting Installation

2. Physical Introduction

5. Connecting the Antennas and 

  Powering It Up

6. Web Login

Отзывы: