Planet IPX-600 Скачать руководство пользователя

Страница: 17 / 67

Network Setup

Click the

Network Setup

item on the main menu; you will see the following web page.

LAN

: You can change the LAN IP Address and Subnet Mask of the IPX-600 here. If there

is already another DHCP server or another NAT/Router device existed in the LAN network,

you must make sure that they are not using the same sub network.

WAN

: You can configure the WAN IP as PPPoE, DHCP or static IP depending on the

internet connection method provided for the IPX-600 in the office.

NTP

: To get the real time from internet, you need to choose the correct Time Zone of your

area. If the default NTP servers cannot work in your area, you have to find the workable

NTP servers and set the values in these fields. (In almost all cases, just use the default

NTP server and everything should be fine).

Figure 12. Network Setup page of IPX-600

DHCP Server

By clicking the

DHCP Server

page, you can configure the DHCP server of the IPX-600. You can

specify the

DHCP Server IP Pool Start IP

and

DHCP Server IP Pool End IP

IPX-600 could possibly get the DNS server from ISP (using PPPoE or DHCP), if you want this

DNS server information passed to DHCP client, you can check on

Provide Real DNS Server

option.

In the

Dynamic DHCP Client List

, you can see the active DHCP client lists.

Содержание IPX-600




































































Результаты поиска

Содержание IPX-600

Отзывы:

Похожие инструкции для IPX-600

Бренды по названию

Популярные бренды

Planet IPX-600, Руководство пользователя

Результаты поиска

Содержание IPX-600

Отзывы:

Похожие инструкции для IPX-600

Бренды по названию

Популярные бренды