Planet IP DSLAM IDL-2400 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 707

background image

IP DSLAM

65

3.8 DSL

This section describes how to configure DSL settings by selecting

DSL

from Function List

Window.

3.8.1 Profile

Allow users to configure Line Profile and Alarm Profile.

3.8.1.1 Line Profile

If to configure Line Profile, double click on

“Line Profile”

from the Function List

Window. The Line Profile configuration window appears.

Field

Definition

Line Type

The ADSL line type, Fast or Interleaved.

Transmit Rate Mode

Defines what form of transmitting rate, Fixed or adaptAtStartup.

Target SNR (dB/10)

Target Signal / Noise Margin. (0-310).

Min Tx Rate(bps)

The minimum transmitting rate of ATU-C side or ATU-R side.

Down Shift SNR (dB/10)

Configured Signal/ Noise Margin for rate downshift. If the noise margin
falls below this level, the modem should attempt to decrease its transmit
rate. In the case that RADSL mode is not present, the value will be 0.

IntCorrectionUP

Sets the correction time for the upstream interleaved buffer. RS can also
be disabled.

Preferred Standard

Preferred standard compliance. Outcome is dependent
upon standard support of the remote unit. GlobespanVirata High Speed
ADSL DMT (ADSL+) applications only.

Maximum Transmit Rate The maximum transmitting rate of ATU-C side or ATU-R side.
Interleave Delay (ms)

The value of Interleave Delay for this channel.

UP Shift SNR (dB/10)

Configured Signal/ Noise Margin for rate upshift. If the noise margin rises
above this level, the modem should attempt to increase its transmit rate.
In the case that RADSL is not present, the value will be 0.

IntCorrectionDown

This parameter sets the correction time for the downstream interleaved
buffer. RS can also be disabled.

Annex Type

This parameter is set as per Annex compliance of the code release.
GlobespanVirata High Speed ADSL DMT (ADSL+) applications only.

«
...
63
64
65
66
67
...
»

Содержание IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IP DSLAM IDL-2400

65014293 - Photoshop CS4 - Mac

Бренд: Adobe Страницы: 87

Бренд: SanDisk Страницы: 11

Бренд: Olympus Страницы: 2

DEVICE FILTER MAC

Бренд: FARONICS Страницы: 30

EliteBook 8460W

Бренд: HP Страницы: 41

Elite 7300 Microtower

Бренд: HP Страницы: 4

MultiSeat ms6000

Бренд: HP Страницы: 63

EliteBook 8560p

Бренд: HP Страницы: 4

Elitebook 8560W

Бренд: HP Страницы: 74

Fabric OS 7.0.0

Бренд: HP Страницы: 138

Бренд: HP Страницы: 50

EliteBook 2560p

Бренд: HP Страницы: 34

Бренд: HP Страницы: 102

Бренд: HP Страницы: 16

Evo D300 - Convertible Minitower

Бренд: HP Страницы: 2

Бренд: HP Страницы: 66

Elite 7500 Microtower

Бренд: HP Страницы: 4

Neoware c50 - Thin Client

Бренд: HP Страницы: 228

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды