- 9 -
- 10 -
- 11 -
- 12 -
- 13 -
- 14 -
User’s Manual
www.PLANET.com.tw
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the power cable to disconnect the device from the power
circuit.Without removing power cable, the device will still consumepower from the power source. In view of Saving the Energy and reducing the unnecessary power
consumption, it isstrongly suggested to remove the power connection for the device if this device is not intended to be active.
PLANET Technology Corp.
2351-AK5020-003
10F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
Warning:
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
►
GSW-1600HP/GSW-2620HP
16/24-Port 10/100/1000T
802.3at PoE+ Ethernet Switch
材質: 100P特銅紙, 水性光
尺寸: 105 x 148 mm(A6), A3三折單張黑白
4.3 Rear Panel
The rear panel of the 802.3at PoE+ Switch indicates an AC
power socket, which accepts input power from 100 to 240V
AC, 50-60Hz, 3.5A/4A.
100~240V AC
50/60Hz
Figure 4-3:
GSW-1600HP Switch Rear Panel
100~240V AC
50 / 60Hz
Figure 4-4:
GSW-2620HP Switch Rear Panel
AC Power Receptacle
Power
Notice
The device is a power-required device, which
means it will not work till it is powered. If
your networks should be active all the time,
please consider using UPS (Uninterrupted Power
Supply) for your device. It will prevent you
from network data loss or network downtime.
Power
Notice
In some areas, installing a surge suppression
device may also help to protect your 802.3at
PoE+ Switch from being damaged by
unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 4:
Follow the same steps to attach the second
bracket to the opposite side.
Step 5:
After the brackets are attached to the 802.3at
PoE+ Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5-2.
Figure 5-2:
Mounting the 802.3at PoE+ Switch in a Rack
Step 6:
Connect your 802.3at PoE+ Switch to
802.3af/802.3at complied PDs and other network
devices.
A. Connect one end of a standard network cable to the
10/100/1000BASE-T RJ45 ports on the front panel of
the 802.3at PoE+ Switch.
B. Connect the other end of the cable to the network
devices such as printer servers, workstations or
routers, etc.
5. Hardware Installation
5.1 Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard
rack, follow the instructions described below.
Step 1:
Place your 802.3at PoE+ Switch on a hard flat
surface, with the front panel positioned towards
your front side.
Step 2:
Attach a rack-mount bracket to each side of
the 802.3at PoE+ Switch with supplied screws
attached to the package. Figure 5-1 shows how to
attach brackets to one side of the 802.3at PoE+
Switch.
Figure 5-1:
Attaching the Brackets to the 802.3at PoE+ Switch.
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
the warranty.
Step 3:
Secure the brackets tightly.
Step 7:
Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at
PoE+ Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the 802.3at PoE+ Switch receives power, the Power
LED should remain solid Green.
5.2 Installing the SFP Transceiver
(GSW-2620HP only)
The sections describe how to insert an SFP transceiver into
an SFP slot of the GSW-2620HP.
The SFP transceivers are hot-pluggable and hot-swappable.
You can plug in and out the transceiver to/from any SFP
port without having to power down the GSW-2620HP, as
the Figure 5-3 shows.
MGB-Series
SFP Transceiver
LC Fiber Cable
1
2
Figure 5-3:
Plug In the SFP Transceiver
Approved PLANET SFP Transceivers
PLANET GSW-2620HP supports both single mode and
multi-mode SFP transceiver. The following website link of
approved PLANET SFP transceivers is correct at the time of
publication:
http://www.planet.com.tw/en/product/product.php?id=11027
Note
It is recommended to use PLANET SFP on the
GSW-2620HP. If you insert an SFP transceiver
that is not supported, the GSW-2620HP will not
recognize it.
1.
Before we connect the GSW-2620HP to the other
network device, we have to make sure both sides of
the SFP transceivers are with the same media type, for
example, 1000BASE-SX to 1000BASE-SX; 1000BASE-LX
to 1000BASE-LX.
2. Check whether the fiber-optic cable type matches with
the SFP transceiver requirement.
To connect to 1000BASE-SX SFP transceiver, please
use the multi-mode fiber cable with one side being the
male duplex LC connector type.
To connect to 1000BASE-LX SFP transceiver, please
use the single-mode fiber cable with one side being
the male duplex LC connector type.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site first to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
