- 6 -
- 7 -
- 5 -
1. Network
Configuration
4) ‘Operation successful’ will be reported if it’s done properly.
Note:
If you want to quit, press
‘**’
.
1.5 DNS
1) Pick up phone and press
‘****’
to start IVR;
2) Choose
‘1’
and then
‘5’
, and the VIP-1000PT/VIP-1000T will report on
the current
DNS
.
3) Input the new DNS and end with
‘#’
.
Use
‘*’
to replace
‘.’
. User can input
192*168*20*1
to set the
new DNS
192.168.20.1
.
Press the
‘#’
key to indicate that you have finished.
4) ‘Operation successful’ will be reported if it’s done properly.
Note:
If you want to quit, press
‘**’
.
2. Phone Port
Configuration
2.1 Phone Number
1) Pick up phone and press
‘****’
to start IVR;
2) Choose
‘2’
and then
‘1’
, and the VIP-1000PT/VIP-1000T will report on
the current
Phone Number
.
Note:
If you want to quit, press
‘**’
.
2.2 Server IP Address
1) Pick up phone and press
‘****’
to start IVR;
2) Choose
‘2’
, and the VIP-1000PT/VIP-1000T will report on the current
Server IP Address
.
Note:
If you want to quit, press
‘**’
.
3. Factory
Reset
1) Pick up phone and press
‘****’
to start IVR.
2) Choose
‘3’
, and the VIP-1000PT/VIP-1000T will report on
‘Factory
reset’
.
3) At the prompt,
please enter password
. Please refer to Operation 1
for the password input.
4) ‘Operation successful’ will be reported if password is right and then the
VIP-1000PT/VIP-1000T will be set to factory default.
5) Press
‘4’
to reboot to make changes effective.
Note:
If you want to quit, press
‘**’
.
4. Reboot
1) Pick up phone and press
‘****’
to start IVR;
2) Choose
‘4’
, and the VIP-1000PT/VIP-1000T will report on
‘Reboot’
.
3) At the prompt,
please enter password
. Refer to Operation 1 for the
password input.
4) The VIP-1000PT/VIP-1000T will reboot if password is right and
operation is done properly.
Note:
If you want to quit, press
‘**’
.
5. WAN
Port Login
1) Pick up phone and press
‘****’
to start IVR;
2) Choose
‘5’
, and the VIP-1000PT/VIP-1000T will report on the
‘WAN
Port Login’
;
3) At the prompt,
please enter password
. Please refer to Operation 1
for the password input.
4) ‘Operation successful’ will be reported if operation is properly done.
5) At the prompt
‘1-enable 2-disable’
, choose 1 or 2, and end with
‘#’
.
6) ‘Operation successful’ will be reported if it’s done properly.
Note:
If you want to quit, press
‘**’
.
6. Web
Access Port
1) Pick up phone and press
‘****’
to start IVR;
2) Choose
‘6’
, and the VIP-1000PT/VIP-1000T will report on
‘Web
Access Port’
.
3) At the prompt,
please enter password
. Please refer to Operation 1
for the password input.
4) ‘Operation successful’ will be reported if operation is properly done.
5) Reports on the current
Web Access Port
;
6) Set the new
Web access port
and end with
‘#’
.
7) ‘Operation successful’ will be reported if it’s done properly.
Note:
If you want to quit, press
‘**’
.
7. Software
Version
1) Pick up phone and press
‘****’
to start IVR.
2) Choose
‘7’
, and the VIP-1000PT/VIP-1000T will report on the current
‘Firmware version’
.
Note:
If you want to quit, press
‘**’
.
4. NOTICE
In the Voice menu, press
*
(asterisk) to return to the up level menu.
If any changes are made in the IP assignment mode, please reboot the VIP-1000PT/
VIP-1000T to take effect the settings.
When entering IP address or subnet mask, input
‘*’
to represent
‘.’
and add
‘#’
to
finish inputting, for example, to enter the IP address
192.168.1.11
, press these
keys:
192*168*1*11#
.
You can enter the password by phone keypad; the matching table between numbers
and letters are as follows:
To input: A,B,C,a,b,c------press ‘2’
To input: D,E,F,d,e,f------press ‘3’
To input: G,H,I,g,h,i------press ‘4’
To input: J,K,L,j,k,l------press ‘5’
To input: M,N,O,m,n,o------press ‘6’
To input: P,Q,R,S,p,q,r,s------press ‘7’
To input: T,U,V,t,u,v------press ‘8’
To input: W,X,Y,Z,w,x,y,z------press ‘9’
To input all other characters in the administration password------press ‘0’.
Press the
‘#’
(pound) key to indicate that you have finished entering the IP address or
subnet mask or other settings.
When assigning IP address in static IP mode, customer must set IP address, subnet
mask and default gateway. If in DHCP mode, please make sure that DHCP server is
available in your existing broadband connection to which WAN port of the VIP-1000PT/
VIP-1000T is connected.
Further Information
For further configuration, please refer to the user’s manual, which can be downloaded
from the website.
http://www.planet.com.tw/en/support/download.php?type1=372&model=48762&type=3
If you have any other question, please contact the dealer where you
purchased this product or you can contact PLANET directly at the
following email address: [email protected]
2011-D10570-001
