manualshive.com logo in svg

Planet Networking & Communication FRT-415N, Руководство пользователя

Поделиться
Скачать
Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 92

User Manual of FRT-415N 

 

 

92

5.7.1.2 Backup/Restore 

Click 

Backup/Restore

 in the left pane and the page shown in the following figure appears. You can back up 

the current settings to a file and restore the settings from the file that was saved previously. 

 

Figure 5-70 

Backup/Restore 

 

The following table describes the parameters: 

Field 

Description 

Save Settings to File 

Click it and select the path. Then you can save the configuration file of 
the router. 

Load Settings from File 

Click 

Browse

 or 

Choose File

 to select the configuration file. 

Upload 

After selecting the configuration file of the router, click 

Upload

 to start 

uploading the configuration file of the router. 

5.7.2 Password 

Choose

 Maintenance 

>

 Password

 and the page shown in the following figure appears. By default, the user 

name and password of the administrator are 

admin

 and 

admin

 respectively. The user name and password of 

the common user are 

user

 and 

user

 respectively. 

Содержание FRT-415N






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды