Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 91

Страница: 91 / 117

User Manual of FRT-415N

5.7 Maintenance

In the navigation bar, click Maintenance. The Maintenance page displayed contains

Update

Password

Reboot

Time

Log

and

Diagnostics

5.7.1 Update

Choose

Maintenance

Update

. The

Update

page displayed contains

Upgrade Firmware

and

Backup/Restore

Do not turn off the router or press the Reset button while the procedure is in progress.

5.7.1.1 Firmware Update

Click

Firmware

Update in the left pane and the page shown in the following figure appears. On this page, you

can upgrade the firmware of the router.

Figure 5-69

Firmware Update

The following table describes the parameters:

Field

Description

Select File

Click

Browse

Choose File

to select the firmware file.

Upload

After selecting the firmware file, click

Upload

to start upgrading the

firmware file.

Reset

Click it to start selecting the firmware file.

Содержание FRT-415N






















































































































Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication FRT-415N, Руководство пользователя

Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды