Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 82

Страница: 82 / 117

User Manual of FRT-415N

5.6 Firewall

Choose Service >

Firewall

and the Firewall page that is displayed contains

MAC Filter

IP/Port Filter

URL Filter

ACL, DoS

and

Parent Control

5.6.1 MAC Filter

Click

MAC Filter

in the left pane and the page shown in the following figure appears. Entries in the table are used

to restrict certain types of data packets from your local network to Internet through the gateway. These filters are
helpful in securing or restricting your local network.

Figure 5-60

MAC Filter

The following table describes the parameters:

Field

Description

Outgoing Default Policy

Specify the default action on the LAN to WAN bridging/forwarding path.

Incoming Default Policy

Specify the default action on the WAN to LAN bridging/forwarding path.

Direction

Traffic

Outgoing

Incoming

direction.

Action

Deny or allow traffic when matching this rule.

Source MAC

The source MAC address must be xxxxxxxxxxxx format.

Destination MAC

The destination MAC address must be xxxxxxxxxxxx format.

Содержание FRT-415N






















































































































Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication FRT-415N, Руководство пользователя

Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды