manualshive.com logo in svg

Planet Networking & Communication FRT-415N, Руководство пользователя

Поделиться
Скачать
Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 74

User Manual of FRT-415N 

 

 

74

5.5 Service 

In the navigation bar, click 

Service

. On the 

Service

 page that is displayed contains 

IGMP

,

 UPnP

,

 DNS

 and 

DDNS

. 

5.5.1 IGMP 

5.5.1.1 IGMP Proxy 

Choose 

Service

 > 

IGMP 

and the page shown in the following figure appears. IGMP proxy enables the system to 

issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The 
system acts as a proxy for its hosts after you enable it. 

 

Figure 5-54 

IGMP Proxy 

 

The following table describes the parameters: 

Field 

Description 

IGMP Proxy 

The Internet Group Management Protocol

.

 

Enable/Disable the function 

to access. 

Multicast Allowed 

Enable/Disable the function to access. 

Robust Count 

Robust factor of the IGMP Proxy Counter. 

Last Member Query 
Count  

The last-member query interval is the maximum amount of time between 
group-specific query messages, including those sent in response to 
leave-group messages. You can configure this interval to change the 
amount of time it takes a routing device to detect the loss of the last 
member of a group. 

Содержание FRT-415N






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды