Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 38

Страница: 38 / 117

User Manual of FRT-415N

5.3.2 LAN

Choose Setup >

LAN

. The

LAN

page that is displayed contains

LAN,

DHCP,

DHCP Static and LAN IPv6

5.3.2.1 LAN

Click

LAN

in the left pane and the page shown in the following figure appears. On this page, you can change IP

address of the router. The default IP address is

192.168.1.1

, which is the private IP address of the router.

Figure 5-17

LAN

The following table describes the parameters:

Field

Description

IP Address

The IP address of your LAN hosts is used to identify the device’s LAN
port.

Subnet Mask

Enter the subnet mask of LAN interface.

Secondary IP

Select it to enable/disable a secondary LAN IP address. The two LAN
IP addresses must be in the different network.

IGMP Snooping

Enable

Disable

the IGMP snooping function for the multiple bridged

LAN ports.

MAC Address Control

It is the access control based on MAC address. Select LAN1, LAN2,
LAN3, LAN4, WLAN and the host whose MAC address listed in the
Currently Allowed MAC Address Table can access the device. Then

Содержание FRT-415N






















































































































Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication FRT-415N, Руководство пользователя

Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды