manualshive.com logo in svg

Planet Networking & Communication FRT-415N, Руководство пользователя

Поделиться
Скачать
Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 26

User Manual of FRT-415N 

 

26 

Chapter 5. System Settings

 

Determining your Connection Settings 

Before you configure the router, you need to know the connection information supplied by your Internet 
service provider. 

Connecting the Fiber Router to your Network 

Unlike a simple hub or switch, the setting up of the Fiber Router consists of more than simply plugging 
everything together. Because the Router acts as a DHCP server, you will have to set some values within the 
Router, and also configure your networked PCs to accept the IP addresses the Router chooses to assign 
them.  

 
Generally there are several different operation modes for your applications. And you can know which mode is 
necessary for your system from ISP. These WAN modes are PPPoE, Bridge and IPoE. 

Configuring with Web Browser 

 

It is advisable to change the administrator password to safeguard the security of your network. To configure 
the router, open your browser, type 

“http: //192.168.1.1”

 into the address bar and click 

“Go”

 to get to the 

login page.  

 

Save this address in your Favorites for future reference.   

 

Figure 5-1

 Login the Router 

 

At the User Name prompt, type 

“admin”

, and the Password prompt, type

 “admin”

. You can change these 

later if you wish. Click 

“OK”

 to log in to the router and you can start to configure it now. 

Содержание FRT-415N






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды