Piusi MC BOX B.SMART страница 39 Скачать руководство пользователя

Страница: 39 / 48

/124

/48

This manual is the property of PIUSI S.p.A. Any reproduction, even partial, is forbidden.

translated from Italian

FULL PACK MC BOX etl

At the end of the

dispensing, the relevant

ticket is shown, which

will be stored and made

available for later checks.

Click

DRIVER

HOME

to go

to the user’s

HOME

screen

DRIVER’s

HOME

screen

NOTE

You can also perform the NEW REFILLING procedure offline, i.e. from a

smartphone not connected to the 3/4G or Wi-Fi network.

In this case, the dispensings will be uploaded to the cloud as soon as the

smartphone has the APP open in an area with 3/4G signal, or as soon as

a new smartphone connected to the 3/4G network or Wi-Fi will connect

to the controller.

Содержание MC BOX B.SMART

















































Результаты поиска

Содержание MC BOX B.SMART

Отзывы:

Похожие инструкции для MC BOX B.SMART

Бренды по названию

Популярные бренды

Piusi MC BOX B.SMART, Установка - Использование - Обслуживание

Результаты поиска

Содержание MC BOX B.SMART

Отзывы:

Похожие инструкции для MC BOX B.SMART

Бренды по названию

Популярные бренды