Pirelli ARV3515J-A-GP Скачать руководство пользователя страница 126

Страница: 126 / 142

ROUBLESHOOTING

A-2

LED Indicators

LAN LED is

Off

•

Verify that the VoIP Router and attached device are

powered on.

•

Be sure the cable is plugged into both the VoIP

Router and the corresponding device.

•

Verify that the proper cable type is used and that its

length does not exceed the specified limits.

•

Be sure that the network interface on the attached

device is configured for the proper communication

speed and duplex mode.

•

Check the adapter on the attached device and cable

connections for possible defects. Replace any

defective adapter or cable if necessary.

Network Connection Problems

Cannot ping the

VoIP Router

from the

attached LAN,

or the VoIP

Router cannot

ping any device

on the attached

LAN

•

Verify that the IP addresses are properly configured.

For most applications, you should use the VoIP

Router’s DHCP function to dynamically assign IP

addresses to hosts on the attached LAN. However, if

you manually configure IP addresses on the LAN,

verify that the same network address (network

component of the IP address) and subnet mask are

used for both the VoIP Router and any attached LAN

devices.

•

Be sure the device you want to ping (or from which

you are pinging) has been configured for TCP/IP.

Troubleshooting Chart

Symptom

Action

Содержание ARV3515J-A-GP















































































































































Результаты поиска

Содержание ARV3515J-A-GP

Отзывы:

Похожие инструкции для ARV3515J-A-GP

Бренды по названию

Популярные бренды

Pirelli ARV3515J-A-GP, Руководство пользователя

Результаты поиска

Содержание ARV3515J-A-GP

Отзывы:

Похожие инструкции для ARV3515J-A-GP

Бренды по названию

Популярные бренды