manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

III - INSPECTION

4C11

3.

Scheduled Maintenance

WARNING: GROUND THE MAGNETO PRIMARY CIRCUIT (P LEAD), BEFORE PERFORMING

ANY MAINTENANCE OPERATION ON THE ENGINE.

This section provides instructions for conducting inspections - see Tables III-I (PA-32-260/300) and 
III-II (PA-32R-300). Repair or replacement instructions for those components found to be unserviceable
during inspections will be found in the applicable airplane system section. (See Section Index Guide,
Introduction.)

4.

Description

WARNING: FAILURE TO CONSULT APPLICABLE VENDOR PUBLICATION(S), WHEN

SERVICING OR INSPECTING VENDOR EQUIPMENT INSTALLED IN PIPER
AIRCRAFT,

MAY RENDER THE AIRCRAFT UNAIRWORTHY. (SEE

INTRODUCTION - SUPPLEMENTARY PUBLICATIONS.)

The recurring maintenance schedules for the PA-32-260/300 Cherokee Six and PA-32R-300 Lance are
provided herein as Annual / 100 Hour Inspections. Progressive Inspection Programs will be available
from Piper Dealers in a separate manual form.

Piper inspection programs comply with the F.A.A. Federal Aviation Regulations Parts 43, 91 and 135.
The owner/operator is primarily responsible for maintaining the airplane in an airworthy condition,
including compliance with all applicable Airworthiness Directives and conformity with the requirements
in FAR 91.409, 91.411 and 91.413.

The first overhaul or replacement of components should be performed at the given periods. The
condition of various components can then be used as criteria for determining subsequent periods
applicable to the individual airplane, depending on usage, providing the owner/operator has an
established Part 91 Progressive Inspection Program (see 91.409(d)) or Part 135 Approved Aircraft
Inspection Program (see 135.419).

The time periods given for inspections of various components are based on average usage and
environmental conditions.

NOTE: The listed inspection, overhaul and replacement schedules do not guarantee that a particular

item or component will reach the listed time without malfunction. Unique operating conditions
encountered by individual airplanes cannot be controlled by the manufacturer.

5.

Definitions

A.

Inspections - Must be performed only by Certified Mechanics who are qualified on these aircraft,
using acceptable methods, techniques and practices to determine physical condition and detect
defects.

(1) Routine Inspection - Consists of a visual examination or check of the aircraft and its

components and systems without disassembly.

(2) Detailed Inspection - Consists of a thorough examination of the aircraft, appliance, component,

or system; with disassembly as necessary to determine condition.

(3) Special Inspection - Involves those components, systems or structure which by their

application or intended use require an inspection peculiar to, more extensive in scope or at a
time period other than that which is normally accomplished during an event or annual
inspection.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Squirrel Aura 2 User Manual preview
Aura 2
Бренд: Squirrel Страницы: 8
WRIGHT BROTHERS GAMBLER AG Instruction Manual preview
GAMBLER AG
Бренд: WRIGHT BROTHERS Страницы: 14
ASG 32 EL Flight Manual preview
32 EL
Бренд: ASG Страницы: 10
Helio HT-295 Owner'S Manual preview
HT-295
Бренд: Helio Страницы: 28
MACFLY PARAMOTORS TRIKE TANDEM User Manual preview
PARAMOTORS TRIKE TANDEM
Бренд: MACFLY Страницы: 20
Core GTS6 Manual preview
GTS6
Бренд: Core Страницы: 12
Symphony SA-160 Flight Manual preview
SA-160
Бренд: Symphony Страницы: 338
PRO-DESIGN B-SAFE 140 Owner'S Manual preview
B-SAFE 140
Бренд: PRO-DESIGN Страницы: 15
Flanders Silent Twin User Manual preview
Silent Twin
Бренд: Flanders Страницы: 9
Aquila AT01-100A Handbook preview
AT01-100A
Бренд: Aquila Страницы: 20
Aquila AT01-100A 2021 Pilot Operating Handbook preview
AT01-100A 2021
Бренд: Aquila Страницы: 42
Axis VENUS SC Pilot'S Manual preview
VENUS SC
Бренд: Axis Страницы: 22
Piper Navajo Chieftain PA-31-350 Service Manual preview
Navajo Chieftain PA-31-350
Бренд: Piper Страницы: 950

Бренды по названию

Популярные бренды

Загрузить еще бренды