Piper Cherokee LANCE страница 35 Скачать руководство пользователя | Manualshive

Страница: 35 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

03/27/08

II - HANDLING AND SERVICING

1B11

b.

If the fastener, screw, or nut is listed in Table II-III, but the mating fastener is not listed, tighten only
to the low end of the torque range specified for the listed fastener. In addition, the following
limitations shall apply:

1.

Fastener and nut threads shall be clean and dry (free of lubricants). If the subject
chapter/section requires the fastener and/or nut to be lubricated prior to tightening and does not
specify a torque requirement, use the Table II-III torque range reduced 50 percent.

2.

Table II-III, Sheet 1, shall be used for free running nuts, provided minimal friction drag is
determined as specified below.

3.

The friction drag torque can be determined as follows: Run the nut down to near contact (but
not in contact) with the bearing surface and check the "friction drag torque" required to turn
the nut.

NOTE: Check the friction drag torque by attaching a scale type torque wrench to the nut and

determining the torque required to turn the nut on the bolt. (Before the nut makes
contact with the bearing surface.)

4.

The friction drag torque (if any) shall be added to the desired torque specified in Table II-III,
Sheet 1. This final torque should register on the indicator or be the setting for a snap-over
torque limiting device.

5.

Torque requirements do not apply to cross recessed or slotted screws or to fasteners installed
into rivnuts, pressnuts or other nuts not designed to rotate for wrenching at the fastener unless
otherwise specified in the subject chapter/section.

6.

Fasteners listed in Table II-III installed into nutplates, and which are accessible to be torqued at
the fastener, must be tightened to the low end of the torque range specified in the appropriate
“shear” column. Torque requirements do not apply if the fastener can not be torqued due to
torque device accessibility.

Torque — Inch-Pounds

Tubing

Hose End Fitting

OD

and

Inches

Aluminum - Alloy Tubing

Steel Tubing

Hose Assemblies

Minimum

Maximum

Minimum

Maximum

Minimum

Maximum

1/8

20

30

———

———

———

———

3/16

30

40

90

100

70

120

1/4

40

65

135

150

100

250

5/16

60

85

180

200

210

420

3/8

75

125

270

300

300

480

1/2

150

250

450

500

500

850

5/8

200

350

650

700

700

1150

3/4

300

500

900

1000

———

———

7/8

500

600

1000

1100

———

———

1

500

700

1200

1400

———

———

1-1/4

600

900

———

———

———

———

1-1/2

600

900

———

———

———

———

TABLE II-II. FLARE FITTING TORQUE VALUES

(PIR-AC65-9A.)

«
...
33
34
35
36
37
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: Amewi Страницы: 24

Бренд: Carl Goldberg Products Страницы: 10

Бренд: Scott Sport Страницы: 27

Бренд: North Wing Страницы: 101

Бренд: Swing Страницы: 28

Бренд: STEMME Страницы: 215

Бренд: Aerola Страницы: 21

Бренд: Rans Страницы: 249

Бренд: Wills Wing Страницы: 69

Cessna 680 Citation Sovereign

Бренд: Textron Страницы: 12

Cessna Citation Excel 5355

Бренд: Textron Страницы: 29

TL-2000 Sting S4

Бренд: TL Ultralight Страницы: 62

Harness ACRO3 L

Бренд: SUPAIR Страницы: 27

Бренд: SUPAIR Страницы: 41

Бренд: Piper Страницы: 356

Бренд: Piper Страницы: 752

Бренд: Piper Страницы: 78

Бренд: Aviation Artur Trendak Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды