manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

VA - HYDRAULIC SYSTEM

07/15/06

1J22

8.

With the glide established, turn the adjustment screw (2) clockwise until the gear drops. (First
indication of gear dropping will be that the gear unsafe light comes ON.)

9.

Climb again to a safe altitude and check that the gear drops at the correct airspeed.

10. Land the airplane and tighten the adjustment screw jam nut (28). 

c.

To check adjustment of electrical switch, the following procedure may be used:

1.

Place the airplane on jacks. (Refer to Jacking, Section II.)

2.

Move the mixture control back to idle cut-off and the throttle to full forward to prevent gear
warning horn from sounding during adjustment.

3.

Ascertain that the actuator tension springs are properly adjusted according to Step a.

4.

Retract the landing gear hydro-electrically by turning the master switch ON, raising the
emergency gear extension lever and moving the gear selector switch to the up position. The
emergency gear extension lever must be retained in the up position to keep the gear up.

5.

Check for proper switch operation by the following procedure:

(a) Turn master switch ON and move gear selector switch to the up position. Pump should

not operate.

(b) Move the emergency gear extension lever to the up override position. Pump should

operate and gear should retract.

(c) With selector lever up, slowly lower emergency gear extension lever to allow gear to drop

to down position. The pump should not operate at any time during extension.

(d) Turn master switch OFF.

6.

Check gear operation in the normal manner with the use of the gear selector switch. The
emergency extension lever must be held in the up override position.

7.

Ascertain that gear is down and locked and remove airplane from jacks. Then flight check the
retractable landing gear system. (Refer to Paragraph 5A-14a.)

5A-14a. OPERATIONAL CHECK OF RETRACTABLE LANDING GEAR SYSTEM. 

a.

Maximum Gear Extend: Place the gear selector in the down position at 150 MPH (130 Kts). In
approximately 5 to 10 seconds the three green gear lights should be on indicating that the gear is
down and locked. 

b.

Minimum Gear Retract: Allow approximately 8 seconds for the pressure in the hydraulic system to
normalize between gear extension and retraction. Place the selector switch in the UP position at 125
MPH (109 Kts). In approximately 5 to 10 seconds all the gear indicating lights should be out,
indicating that the gear is fully retracted. 

c.

Override Gear Down and Up:

1.

Down: Establish a normal glide at approximately 130 MPH (113 Kts), with power at idle.
Slowly move the override lever down, while observing the ammeter to confirm that the
hydraulic pump does not start. The gear should go down and lock. Move the gear selector
switch down. Release the override lever. The gear should remain down.

2.

Up: Set maximum climb power. Maintain approximately 80 MPH (70 Kts) for approximately
15 seconds. Move the gear selector switch to the up position. The gear should not retract. Pull
the override lever up. The gear should retract. Allow the airspeed to increase to at least 130
MPH (113 Kts). Release the override lever and the gear should remain up.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

ICARO 2000 Piuma Bip Owner'S Manual preview
Piuma Bip
Бренд: ICARO 2000 Страницы: 44
F-One BANDIT 2017 User Manual preview
BANDIT 2017
Бренд: F-One Страницы: 21
Swing Astral 3 Manual preview
Astral 3
Бренд: Swing Страницы: 16
Advance acoustic Pl 3 Manual preview
Pl 3
Бренд: Advance acoustic Страницы: 19
Quickie Q2 Lite Owner'S Manual preview
Q2 Lite
Бренд: Quickie Страницы: 84
Nova ARGON 20 Manual preview
ARGON 20
Бренд: Nova Страницы: 76
Tecnam P2008 JC Flight Manual preview
P2008 JC
Бренд: Tecnam Страницы: 264
TOMAHAWK SPORT Cyclone Instruction Manual preview
Cyclone
Бренд: TOMAHAWK SPORT Страницы: 36
Beechcraft C-12C Operator And Technical Reference Manual preview
C-12C
Бренд: Beechcraft Страницы: 949
SKY PARAGLIDERS AEON L User Manual preview
AEON L
Бренд: SKY PARAGLIDERS Страницы: 42
Ozone Atom 3 Pilot'S Manual preview
Atom 3
Бренд: Ozone Страницы: 18
Rans S-20 RAVEN Text Manual preview
S-20 RAVEN
Бренд: Rans Страницы: 249
Thoma Modelltechnik ORBIS 20'' Installation And Operating Manual preview
ORBIS 20''
Бренд: Thoma Modelltechnik Страницы: 33
JOJO WINGS XF 15 Manual preview
XF 15
Бренд: JOJO WINGS Страницы: 33
EScale ElectraGlide Assembly Instructions Manual preview
ElectraGlide
Бренд: EScale Страницы: 16
AirBorne WindSports Sting 3 Owner'S And Service Manual preview
Sting 3
Бренд: AirBorne WindSports Страницы: 54
APCO Aviation CRUISER 400 Manual preview
CRUISER 400
Бренд: APCO Aviation Страницы: 16
APCO Aviation LIFT 450 Manual preview
LIFT 450
Бренд: APCO Aviation Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды