Piper Cherokee LANCE Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

V - SURFACE CONTROLS

1H19

5-25.

RUDDER CONTROLS.

5-26.

REMOVAL OF RUDDER CONTROL CABLES. (Refer to Figure 5-10.)

a.

To remove either the forward (13 and 14) or aft (17 and 18) rudder cables, first remove the access
panel to the aft section of the fuselage.

b.

Disconnect the desired cable at the turnbuckle (15 or 16) in the aft section of the fuselage.

c.

Either forward rudder cable (13 or 14) may be removed by the following procedure:

1.

Remove the tunnel cover in the aft area of the cabin by removing the carpet over the tunnel and
the cover attachment screws.

2.

Remove the cable guard plate(10) from the underside of the pulley cluster (12) that is located
in the aft area of the floor tunnel, by removing the guard attachment screws.

3.

Remove the floor panel located directly aft of the main spar by removing the center seats, seat
belt attachments and the screws securing the floor panel. Lift the panel and remove from
airplane.

4.

From within the area of the floor opening, remove the cable rub blocks (6) that are attached to
the spar housing by removing the block attachment screws. Also remove the cable guard pin(9)
at the pulley(8) cluster in the aft area of the opening by removing a cotter pin from one end of
the guard.

5.

Remove the fuel selector panel cover by removing the rudder trim knob and the cover
attachment screws.

6.

Remove the lower selector cover, and the fuel selector control lever by removing the
attachment pin, at the bottom of the lever, that holds the lever on the selector torque tube.

7.

Remove the tunnel plate just aft of the tee bar by removing enough carpet from the tunnel to
allow the plate attachment screws and the plate to be removed .

8.

Remove the forward heat duct from one side of the floor tunnel. (Preferably from the side from
which the control cable is to be removed. )

9.

Move the cable guard (4) located under the pulley cluster (5) and below the fuel selector by
removing the cotter pin from the exposed end and sliding it to the left or right as required,

10. Disconnect the end of the cable from the arm on the rudder pedal torque tube by removing the

cotter pin, nut, washer and bolt (2).

11. Draw the cable from the floor tunnel.

d.

The aft rudder control cables (17 and 18) may be removed by the following procedure:

1.

Remove the tail cone by removing its attachment screws.

2.

Disconnect the cable from the rudder horn (20) by removing cotter pin, nut, washer and bolt
(19).

3.

Draw the cable through the fuselage.

«
...
173
174
175
176
177
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: ICARO Страницы: 17

Бренд: Gradient Страницы: 18

P-51 GALLOPING GHOST

Бренд: H-KING Страницы: 19

Бренд: Swing Страницы: 60

Бренд: SOL paragliders Страницы: 24

Бренд: MAC PARA Страницы: 40

L-23 Super Blanik

Бренд: LET Страницы: 70

Бренд: Ozone Страницы: 39

Бренд: Magni Gyro Страницы: 115

Бренд: Ozone Страницы: 37

Бренд: Way Страницы: 22

Бренд: NEO Страницы: 21

HC-C2YR-4CF/FC8475-6

Бренд: Hartzell Страницы: 306

Бренд: Whirlwind Страницы: 29

PA-28RT-201T TURBO ARROW IV

Бренд: Piper Aircraft Corporation Страницы: 139

Cherokee Arrow II

Бренд: Piper Aircraft Corporation Страницы: 142

TWIN COMANCHE PA-30

Бренд: Piper Aircraft Corporation Страницы: 863

PA-28-161 CADET

Бренд: Piper Aircraft Corporation Страницы: 422

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды