Piper Cherokee LANCE Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

V - SURFACE CONTROLS

1H17

5-24.

INSTALLATION OF RUDDER AND STEERING PEDAL ASSEMBLY. (Refer to Figure 5-9.)

a.

Assemble the torque tube assembly (1, 2, 3 and 4) as shown in Figure 5-9. Do not at this time install
the two bolts (25 and 26) through the center of the tube assembly.

b.

Place the upper support blocks (7) on the ends of the torque tube assembly. Note that a washer (9) is
required on each end of the tube.

c.

Position the support blocks (7 and 8) on their mounting brackets at each side of the fuselage and
secure with bolts, washers and nuts. Note that a bushing is required in the bolt holes of the upper
support block, and a plate on top of the upper block, between the upper and lower blocks and under
the block mounting bracket .

d.

Align the bolt holes in the center area of the torque tube assembly, install bolts, washers and nuts
(25 and 26) and tighten.

e.

Position the torque tube support bracket (35) on the floor tunnel and secure with bolts,

f.

Position the vee brace(s) (29) on the torque tube, install the strap bracket (28) around the torque
tube and brace, and secure with bolts, washers and nuts (27) .

g.

Check that the rod end (18) on the clevis rod (15) is adjusted to give a dimension of 7.94 inches
between hole centers .

h.

Connect the ends of the brake cylinder rods (11) and clevis rods (15) to the idler arms (10) and
secure with clevis and cotter pins (13).

i.

Connect the steering rods (21) to the rudder pedals (32 and 33) and secure with bolts and nuts (24).
Check steering rod adjustment per Alignment of Nose Gear, Section VI.

j.

Connect the rudder trim to the arm of the torque tube and secure with bolt, washer, nut and cotter
pin. A thin washer is installed under the nut which is tightened only finger tight.

k.

Connect the ends of the rudder control cables (19) to the arms provided on the torque tube and
secure with bolts, washers, nuts and cotter pins (20). Allow the ends free to rotate.

l.

Swing the tee bar into place and secure with attachment bolts, washers and nuts (15) with the bolts
inserted in through each side of the floor tunnel.

m.

Connect the stabilator control cables (11) to the lower end of the tee bar with bolt, washer and nut
(16), and secure with cotter pin. Allow the cable ends free to rotate.

n.

Set rudder cable tension and check rigging and adjustment per paragraph 5-32.

o.

Set stabilator cable tension and check rigging and adjustment per paragraph 5-15.

p.

Check aileron cable tension.

q.

Check safety of bolt and turnbuckles.

r.

Install the floor tunnel plate and secure with screws. Fasten the tunnel carpet in place.

s.

Install the fuel selector lever on the selector torque tube, secure with clevis pin and safety with
cotter pin.

t.

Install the fuel selector covers and the rudder trim control knob.

u.

Install the access to the aft section of the fuselage.

«
...
171
172
173
174
175
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: Slingsby Страницы: 35

Бренд: PLKB Страницы: 12

Бренд: STEMME Страницы: 211

Бренд: Zenair Страницы: 29

Бренд: Rand-Kar Страницы: 72

Бренд: Rans Страницы: 82

Бренд: Apogee Страницы: 8

Бренд: Aircraft Industries Страницы: 55

Бренд: Mooney Страницы: 8

Бренд: Mooney Страницы: 42

Ranger M20C 1968

Бренд: Mooney Страницы: 93

Executive 21 1968

Бренд: Mooney Страницы: 92

Бренд: Mooney Страницы: 96

Бренд: Mooney Страницы: 164

M20V Acclaim Ultra

Бренд: Mooney Страницы: 265

Бренд: Mooney Страницы: 377

Бренд: Mooney Страницы: 437

Бренд: Flanders Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды