manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

V - SURFACE CONTROLS

07/15/06

1H16

5-21a. PIPER ELECTRIC TRIM (PET) SYSTEM

If installed, the Piper Electric Trim System adds a servo on the stabilator trim cable and incorporates a
pressure sensor assembly/switch into the pitot-static system. See the Pitch Trim System Service Manual,
P/N 753-771 for adjustment/calibration.

5-22.

RUDDER AND STEERING PEDAL ASSEMBLY.

5-23.

REMOVAL OF RUDDER AND STEERING PEDAL ASSEMBLY. (Refer to Figure 5 -9.)

a.

Remove the access panel to the aft section of the fuselage.

b.

Relieve rudder and stabilator cable tension by loosening one of the rudder and stabilator cable
turnbuckles in the aft section of the fuselage.

c.

Remove the fuel selector panel cover by removing the rudder trim knob and the cover attachment
screws.

d.

Remove the lower selector cover and disconnect the fuel selector control lever from the selector
torque tube by removing the attachment pin located at the bottom of the lever.

e.

Remove the tunnel plate just aft of the tee bar by laying back enough tunnel carpet to remove the
plate attachment screws.

f.

Disconnect the stabilator control cable from the lower end of the tee bar assembly.

g.

Remove the tee bar attachment bolts with their washers and nuts which are through each side of the
floor tunnel. Pull the lower end of the tee bar aft.

h.

Disconnect the control cable (19) ends from the arms on the torque tube (3) by removing the cotter
pins, washers, nuts and bolts (20).

i.

Disconnect the rudder trim from the torque tube assembly by removing the cotter pin, washers and
bolt that connects the arm to the trim.

j.

Disconnect the steering rods (21) at the rudder pedals (32 and 33) by removing nuts and bolts (24).

k.

Disconnect the brake cylinders (12) at the lower end of each cylinder rod (11) by removing the
cotter pins, washers, nuts and bolts (20).

l.

Disconnect the vee brace(s)(29) (two braces are used with right hand brakes) from the torque tube
by removing nuts, washers and bolts (27) that secure the strap bracket (28) to the vee brace.

m.

If an AutoPilot amplifier is installed over the torque tube at the right side of the fuselage, disconnect
the electrical plug and release the two fasteners that secure it to its mounting bracket.

n.

Disconnect the torque tube support bracket (35) where it attaches to the floor tunnel by removing its
attachment bolts.

o.

Remove the two bolts (25 and 26) that extend through the torque tube and are located at the center
of the tube assembly over the floor tunnel. Compress the tubes .

p.

Disconnect the torque tube support blocks (7 and 8) from their support brackets on each side of the
fuselage by removing the attachment nuts, washers and bolts (6).

q.

Remove the trim side panels, if desired.

r.

Remove the assembly from the airplane. Note the spacer washer (9) on each end and between the
support blocks.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

AVEKO Evolution VL-3E-1 Pilot Operating Handbook preview
Evolution VL-3E-1
Бренд: AVEKO Страницы: 40
CrazyFly Foil User Manual preview
Foil
Бренд: CrazyFly Страницы: 2
U-Turn BLACKOUT PLUS Manual preview
BLACKOUT PLUS
Бренд: U-Turn Страницы: 42
Cessna 172 Series 1973 Owner'S Manual preview
172 Series 1973
Бренд: Cessna Страницы: 77
Cessna 172 Skyhawk SERIES Maintenance Manual preview
172 Skyhawk SERIES
Бренд: Cessna Страницы: 167
Gulfstream G200 Manual preview
G200
Бренд: Gulfstream Страницы: 13
SKY PARAGLIDERS DRIVE II User Manual preview
DRIVE II
Бренд: SKY PARAGLIDERS Страницы: 72
Ocean Rodeo ALUULA G Series Repair Instructions preview
ALUULA G Series
Бренд: Ocean Rodeo Страницы: 4
Nervures FITZ ROY Owner'S Manual preview
FITZ ROY
Бренд: Nervures Страницы: 28
Skywalk Pepper Cross Light 110 Manual/Service preview
Pepper Cross Light 110
Бренд: Skywalk Страницы: 12
Flow Paragliders VISSTA Manual preview
VISSTA
Бренд: Flow Paragliders Страницы: 19
Crosswinds Aviation DA20 C1 Eclipse Training Manual preview
DA20 C1 Eclipse
Бренд: Crosswinds Aviation Страницы: 35
AWW Quadrone AW-QDR-BAS Instruction Manual preview
Quadrone AW-QDR-BAS
Бренд: AWW Страницы: 12
PHI MAESTRO 2 light Manual preview
MAESTRO 2 light
Бренд: PHI Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды