Pioneer VSX-933 Скачать руководство пользователя страница 20

Страница: 20 / 131

≫

≫

≫

≫

≫

≫

Speaker Connections and “Speaker Setup” Settings

Connections

(Note) Speaker Impedance

Connect speakers with an impedance of 4 Ω to 16 Ω. If any of the speakers

to be connected has an impedance of 4 Ω or more and 6 Ω or less, the setting

is required in the System Setup menu after the Initial Setup (

p112

) is

completed. Press

on the remote controller, and in the Home displayed set

"System Setup" - "Speaker" -"Configuration" - "Speaker Impedance" to "4ohms".

Connect the Speaker Cables

1/2˝

(12 mm)

Make correct connection between the unit's jacks and speaker's jacks (+ side to

+ side, and - side to - side) for each channel. If the connection is wrong, a bass

sound will not be reproduced properly due to reverse phase. Twist the wires

exposed from the tip of the speaker cable so that the wires do not stick out of the

speaker terminal when connecting. If the exposed wires touch the rear panel,

or the + side and – side wires touch each other, the protection circuit will be

activated.

Содержание VSX-933




































































































































Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды

Pioneer VSX-933, Инструкция по эксплуатации

Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды