Pioneer VSX-520-K, Руководство по эксплуатации

Страница: 40 / 168

Downloaded from www.vandenborre.be
The System Setup menu 06
40
En
Speaker setting
Use this setting to specify your speaker
configuration (size, number of speakers). It is a
good idea to make sure that the settings made
in
Automatically setting up for surround sound
(MCACC) on page 27 are correct.
1 Select ‘SP SET’ from the SP SETUP menu.
2 Use
/
to choose the speaker(s) that
you want to set then select a speaker size.
Use
/
to select the size (and number) of
each of the following speakers:
• Front ( F ) – Select LARGE if your front
speakers reproduce bass frequencies
effectively, or if you didn’t connect a
subwoofer. Select
SMALL to send the bass
frequencies to the subwoofer.
1
• Center ( C ) – Select LARGE if your center
speaker reproduces bass frequencies
effectively, or select
SMALL to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect a center
speaker, choose
NO (the center channel is
sent to the other speakers).
•
Front Height
(
FH
)
2
– Select
LARGE
if your
front height speakers reproduce bass
frequencies effectively. Select
SMALL
to
send bass frequencies to the other
speakers or subwoofer. If you didn’t
connect front height speakers choose
NO
.
•
Surround
(
S
) – Select
LARGE
if your
surround speakers reproduce bass
frequencies effectively. Select
SMALL to
send bass frequencies to the other
speakers or subwoofer. If you didn’t
connect surround speakers choose
NO
(the sound of the surround channels is
sent to the other speakers).
• Surround Back ( SB )
3
– Select the number
of surround back speakers you have (one,
two or none).
4
Select
LARGE
if your
surround back speakers reproduce bass
frequencies effectively. Select
SMALL to
send bass frequencies to the other
speakers or subwoofer. If you didn’t
connect surround back speakers choose
NO .
•
Subwoofer
(
SW
) – LFE signals and bass
frequencies of channels set to
SMALL
are
output from the subwoofer when
YES
is
selected.
5
Choose the
PLUS
setting if you
want the subwoofer to output bass sound
continuously or you want deeper bass (the
bass frequencies that would normally
come out the front and center speakers are
also routed to the subwoofer). If you did not
connect a subwoofer choose
NO
(the bass
frequencies are output from other
speakers).
Note
1 If you select
SMALL
for the front speakers, the subwoofer will automatically be fixed to
YES
. Also, the center, surround,
surround back and front height speakers can’t be set to LARGE if the front speakers are set to SMALL . In this case, all bass
frequencies are sent to the subwoofer.
2 • You can only adjust this setting when PRE OUT is set to HEIGHT .
• If the surround speakers are set to
NO
, the front height speakers will automatically be set to
NO
.
3 You can only adjust the this setting when PRE OUT is set to SURR.BACK .
4 • If the surround speakers are set to NO , the surround back speakers will automatically be set to NO .
• If you select one surround back speaker only, make sure that additional amplifier is hooked up to the PRE OUT L (Single)
terminal.
5 If you can’t get good bass results, listen to the bass response with the subwoofer set to PLUS and YES or the front speakers
set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option
is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
VSX-520_SYXCN_En.book 40 ページ ２０１０年４月１２日 月曜日 午後７時１３分