Pioneer VSX-1120-K, Руководство по эксплуатации

Страница: 62 / 108

Controlling the rest of your system 09
62
En
Chapter 9:
Controlling the rest of your system
Operating multiple receivers
U p to fou r r eceive r s can be o p e r ated disc r etely using this
r eceive r 's r emote cont r ol when using multi p le r eceive r s,
pr ovided they a r e of the same model as this r eceive r . The
r eceive r to be o p e r ated is switched by in p utting the
pr eset code to set the r emote cont r ol setting.
• Set the r emote modes on the r eceive r s befo r e using
this function (see
Remote Control Mode Setup
on
p age 83).
1 Press and hold R.SETUP, then press “4” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess R.SETUP .
2 Press the number button for the receiver (“Receiver
1” to “Receiver 4”) you wish to operate.
Fo r exam p le, to o p e r ate “Receive r 2”, pr ess “ 2 ”.
If the LED lights fo r one second, the setting has been
successfully com p leted.
When the pr eset code is in p ut, the LED flashes th r ee
times to indicate that the setting has failed.
Setting the remote to control other
components
Most com p onents can be assigned to one of the in p ut
function buttons (such as DVD o r CD ) using the
com p onent’s manufactu r e r pr eset code sto r ed in the
r emote.
Howeve r , the r e a r e cases whe r e only ce r tain functions
may be cont r ollable afte r assigning the pr o p e r pr eset
code, o r the codes fo r the manufactu r e r in the r emote
cont r ol will not wo r k fo r the model that you a r e using.
If you can’t find a pr eset code that matches the
com p onent you want to cont r ol, you can still teach the
r emote individual commands f r om anothe r r emote
cont r ol (see
Programming signals from other remote
controls
on p age 63).
Note
• You can cancel o r exit any of the ste p s by pr essing
R.SETUP .
• Afte r one minute of inactivity, the r emote
automatically exits the o p e r ation.
• Fo r g r eate r convenience, assign the TV connected to
the MONITOR OUT te r minal to the TV CTRL button,
and assign you r satellite/cable r eceive r o r set-to p box
connected to the TV in p ut te r minal to the TV in p ut
button. If a single device is connected to both
te
r minals, that device should be assigned to both the
TV CTRL and TV in p ut buttons.
• Devices may be assigned to the following in p ut
function buttons.
Selecting preset codes directly
1 Press and hold R.SETUP, then press “1” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess R.SETUP .
2 Press the input function button for the component
you want to control.
When assigning pr eset codes to TV CONTROL , pr ess TV
CTRL he r e.
The LED blinks once and flashes continuously.
3 Use the number buttons to enter the 4-digit preset
code.
See Preset code list on p age 98.
If the LED lights fo r one second, the setting has been
successfully com p leted.
When the pr eset code is fully in p ut, the LED flashes th r ee
times to indicate that the setting has failed. If this
ha
pp ens, ente r the 4-digit pr eset code again.
4 Repeat steps 2 through 3 for the other components
you want to control.
To t r y out the r emote cont r ol, switch the com p onent on o r
off (into standby) by pr essing  SOURCE . If it doesn’t
seem to wo r k, select the next code f r om the list (if the r e
is one).
5 Press R.SETUP to exit the preset setup mode.
INPUT SELECT TV CTRL
iPod USB TUNER SIRIUS XM
ADAPTER NET RADIO CD TV
BD DVD
R.SETUP
SOURCE RECEIVER MULTI
OPERATION
DVR/BDR HDMI
RECEIVER
VSX-1120_UXJCB.book 62 ページ ２０１０年３月１０日 水曜日 午後２時２分