Basic Setup
04
37
En
• If
Reverse Phase
is displayed, the speaker’s wiring
(+ and –) may be inverted. Check the speaker
connections.
1
– If the connections were wrong, turn off the power,
disconnect the power cord, then reconnect properly.
After this, perform the Full Auto MCACC procedure
again.
– If the connections were right, select
GO NEXT
and
continue.
7
Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings.
Again, try to be as quiet as possible while this is
happening. It may take 3 to 10 minutes.
8
The Auto MCACC Setup procedure is completed and
the Home Menu menu reappears automatically.
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC Setup.
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using
The
Advanced MCACC menu
on page 69 or
The System Setup
and Other Setup menus
on page 78.
2
Problems when using the Auto MCACC Setup
If the room environment is not optimal for the Auto
MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the
microphone) the final settings may be incorrect. Check
for household appliances (air conditioner, fridge, fan,
etc.), that may be affecting the environment and switch
them off if necessary. If there are any instructions
showing in the front panel display, please follow them.
• Some older TVs may interfere with the operation of
the microphone. If this seems to be happening,
switch off the TV when doing the Auto MCACC Setup.
The Input Setup menu
You only need to make settings in the
Input Setup
menu
if you didn’t hook up your digital equipment according to
the default settings (see
Input function default and
possible settings
on page 38). In this case, you need to
tell the receiver what equipment is hooked up to which
terminal so the buttons on the remote control
correspond to the components you’ve connected.
1
Press
on the remote control, then press
HOME MENU.
A Graphical User Interface (GUI) screen appears on your
TV. Use
///
and
ENTER
to navigate through the
screens and select menu items. Press
RETURN
to
confirm and exit the current menu.
2
Select ‘System Setup’ from the Home Menu.
3
Select ‘Input Setup’ from the System Setup menu.
4
Select the input function that you want to set up.
The default names correspond with the names next to the
terminals on the rear panel (such as
DVD
or
VIDEO
)
which, in turn, correspond with the names on the remote
control.
5
Select the input(s) to which you’ve connected your
component.
For example, if your DVD player only has an optical
output, you will need to change the
DVD
input function’s
Digital In
setting from
COAX-1
(default) to the optical
input you’ve connected it to. The numbering (
OPT-1
to
3
)
corresponds with the numbers beside the inputs on the
back of the receiver.
Note
1 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase (dipole speakers, reflective
speakers, etc.),
Reverse Phase
may be displayed even if the speakers are properly connected.
2 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with
different size settings. You can correct the setting manually using the
Manual speaker setup
on page 78.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking
delay and room characteristics into account) and generally does not need to be changed.
• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend
adjusting the settings manually.
RECEIVER
A/V RECEIVER
Exit
Return
a.Manual SP Setup
b. Input Setup
c. OSD Language
d. Network Setup
e. Other Setup
4.System Setup
4b.Input Setup
A/V RECEIVER
Exit
Finish
Input :
DVD
Input Name
:
Rename
Digital In
:
COAX-1
HDMI Input
:
- - -
Input Skip
:
OFF
Component In
:
Comp-1
04he_Basic_setup.fm 37 ページ ２０１０年３月１０日 水曜日 午後２時５１分
Содержание VSX-1120-K
Страница 104: ...Additional information 12 104 En VSX 1120_UXJCB book 104 ページ ２０１０年３月１０日 水曜日 午後２時２分 ...
Страница 105: ...Additional information 12 105 En VSX 1120_UXJCB book 105 ページ ２０１０年３月１０日 水曜日 午後２時２分 ...
Страница 106: ...Additional information 12 106 En VSX 1120_UXJCB book 106 ページ ２０１０年３月１０日 水曜日 午後２時２分 ...
