Pioneer SC-LX73, Руководство по эксплуатации

Страница: 121 / 144

Additional information 13
121
En
Video
Settings
Symptom Remedy
No image is output when an
input is selected. • Check the video connections of the sou r ce component (see page 31).
• Fo r HDMI, o r when digital video conve r sion is set to
OFF
and a TV and anothe r component a r e
connected with diffe r ent co r ds (in Setting the Video options on page 73), you must connect you r TV
to this r eceive r using the same type of video cable as you used to connect you r video component.
• Make su r e the input assignment is co rr ect fo r components connected using component video o r
HDMI cables (see
The Input Setup menu
on page 45).
• Check the video output settings of the sou r ce component.
• Check that the video input you selected on you r TV is co rr ect.
• Some components (such as video game units) have r esolutions that may not be conve r ted. If
adjusting this r eceive r ’s Resolution setting (in
Setting the Video options
on page 73) and/o r the
r esolution settings on you r component o r display doesn’t wo r k, t r y switching Digital Video
Conve r sion (in
Setting the Video options
on page 73) to
OFF
.
Can’t r eco r d video. • Check that the sou r ce is not copy-p r otected.
• The video conve r te r is not available when making r eco r dings. Check that the same type of video
cable is used fo r connecting both the r eco r de r and the video sou r ce (the one you want to r eco r d) to
this r eceive r .
Noisy, inte r mittent, o r disto r ted
pictu r e.
• Sometimes a video deck may output a noisy video signal (du r ing scanning, fo r example), o r the
video quality may just be poo r (with some video game units, fo r example). The pictu r e quality may
also depend on the settings, etc. of you r display device. Switch off the video conve r te r and r econnect
the sou r ce and display device using the same type of connection (component o r composite), then
sta r t playback again.
Video signals a r e not output
f r om the component te r minal.
• When a monito r only compatible with r esolutions of 480i is connected to the component te r minal
and anothe r monito r is connected to the HDMI te r minal, the video signals may not be output to the
monito r connected to the component te r minal. If this happens, do the following:
– Tu r n off the powe r of the monito r connected to the HDMI te r minal.
– Change the
VIDEO PARAMETER
menu
RES
setting.
– Video signals f r om the HDMI te r minal cannot be output to the component te r minals. Input the
video signals f r om the playe r o r othe r sou r ce to the composite o r component te r minals. When using
the component te r minal, assign it at
Input Setup
.
The pictu r e’s movement is
unnatu r al.
• When Resolution unde r
VIDEO PARAMETER
is set to 1080/24p, the pictu r e may not be displayed
p r ope r ly fo r some sou r ce mate r ials. In this case, set the r esolution to something othe r than 1080/24p
(page 73).
Symptom Remedy
The Auto MCACC Setup
continually shows an e
rr o r .
• The ambient noise level may be too high. Keep the noise level in the r oom as low as possible (see
also Problems when using the Auto MCACC Setup on page 44). If the noise level cannot be kept low
enough, you will have to set up the su rr ound sound manually (page 109).
• When using only one su rr ound back speake r , connect it to the
SURROUND BACK L
(Single)
te r minals.
• To use a 5.1-channel speake r set, use the su rr ound speake r s fo r the su rr ound channel, not the
su rr ound back channel.
• Make su r e the r e a r e no obstacles between the speake r s and the mic r ophone.
• If
Reverse Phase
is displayed, t r y the following:
– The speake r ’s wi r ing (+ and –) may be inve r ted. Check the speake r connections.
– Depending on the type of speake r s and thei r installation conditions,
Reverse Phase
may be
displayed even if the speake r s a r e p r ope r ly connected. If this happens, select
GO NEXT
and continue.
– If the speake r is not pointed to the mic r ophone (listening position) o r when using speake r s that
affect the phase (dipole speake r s, r eflective speake r s, etc.), it may not be possible to p r ope r ly identify
the pola r ity.
Afte r using the Auto MCACC
Setup, the speake r size setting
is inco rr ect.
• The r e may have been some low f r equency noise in the r oom f r om an ai r -conditione r , moto r , etc.
Switch off all othe r appliances in the r oom and use Auto MCACC Setup again.
• Depending on a numbe r of facto r s (bass r ep r oduction capabilities of the speake r s, r oom size,
speake r placement, etc.) this may occu r in some cases. Change the speake r setting manually in
Speaker Setting on page 110, and use the ALL (Keep SP System) option fo r the Auto MCACC menu
in
Automatic MCACC (Expert)
on page 99 if this is a r ecu rr ing p r oblem.
SC-LX83_73_DLPW.book 121 ページ ２０１０年５月１９日 水曜日 午後２時７分