background image

9

1

2

3

4

1

2

3

4

C

D

F

A

B

E

S-7EX

3. SCHEMATIC DIAGRAM

5. Acoustic absorbent pads behind the chamber for

the midrange/tweeter

Fig. 2-12: Acoustic absorbent pads behind the chamber

When reattaching, push the 3 acoustic absorbent pads in 
behind the chamber.

Acoustic absorbent pad A:
Lay one acoustic absorbent pad on another and fold them
lengthwise into four.

Acoustic absorbent pad B:
Roll it.

Chamber

Acoustic absorbent pad A

Acoustic absorbent pad B

Acoustic absorbent pad B

INPUT

NETWORK ASSY (SWN1760)

NETWORK ASSY (SWN1761)

L1

3.6mH

1.2mH

68

µ

F/100V

C1

56

µ

F/100V

C2

L2

1.2

R1

s

s

WOOFER

MIDRANGE

TWEETER

White

with Black line

White

White
with Black line

White

White
with Black line

White

White
with Black line

White
with Black line

White

White

White

with Black line

White

INPUT

C1

2.7

µ

F/250V

L1

0.3mH

L2

0.8mH

R3

R2

2.2

/10w

0.47

/10w

0.82mH

L3

C5

15

µ

F/250V

s

s

R1
3

/10w

C3

22

µ

F/250V

C2

12

µ

F/250V

C4

47

µ

F/250V

COIL

L4

1.2mH

s

COIL

C8
15

µ

F/250V

COIL

0.82mH

L5

COIL

COIL

C7

14

µ

F/250V

C6

68

µ

F/100V

S: Winding start side

S: Winding start side

Содержание S-7EX XTW/E











Отзывы: