Pioneer MVH-7300, Руководство по эксплуатации

Страница: 28 / 52

Audio Adjustments
1 Display the audio menu.
Refer to Basic menu operations on page 9.
2 Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
Fader/Balance (fader/balance adjustment)
1
Press
M.C.
to display the setting mode.
2
Push M.C. up or down to adjust the front/rear
speaker balance.
Adjustment range (front/rear):
Front 15 to Rear
15
3
Push
M.C.
left or right to adjust the left/right
speaker balance.
Adjustment range (left/right):
Left 15
to
Right 15
!
Select F/R 0 when only using two speakers.
!
When the rear output setting and preout setting
are
Subwoofer , you cannot adjust front/rear
speaker balance.
Sonic Center Control (sonic center control)
Sound that is suited for the listening position can ea-
sily be created with this function.
1
Press M.C. to display the setting mode.
2
Push
M.C.
left or right to select a listening posi-
tion.
Adjustment range:
Left:7
to
Right:7
Auto EQ
(auto-equalizer on/off)
The auto-equalizer is an equalizer curve created by
auto EQ (refer to
Auto EQ (auto-equalizing) on page
32).
You can turn the auto-equalizer on or off.
1
Press M.C. to turn the auto-equalizer on or off.
You cannot use this function if auto EQ has not been
carried out.
Graphic EQ (equalizer adjustment)
You can adjust the currently selected equalizer curve
setting as desired. Adjusted equalizer curve settings
are stored in
Custom1 or Custom2 .
!
A separate Custom1 curve can be created for
each source. If you make adjustments when a
curve other than
Custom2 is selected, the equali-
zer curve settings will be stored in
Custom1
.
!
A Custom2 curve that is common for all sources
can be created. If you make adjustments when
the
Custom2 curve is selected, the Custom2
curve will be updated.
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to select an equalizer curve.
Powerful
—
Natural
—
Vocal
—
Custom1
—
Cus-
tom2
—
Flat
—
Super Bass
3
Push
M.C.
left or right to select the equalizer
band to adjust.
40Hz
—
80Hz
—
200Hz
—
400Hz
—
1kHz
—
2.5kHz
—
8kHz
—
10kHz
4
Push M.C. up or down to adjust the level of the
equalizer band.
Adjustment range:
+12dB to
–
12dB
Loudness (loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to select the desired setting.
Off (off)
—
Low (low)
—
Mid (mid)
—
High (high)
3
Press M.C. to confirm the selection.
Subwoofer1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output which
can be turned on or off.
1
Press M.C. to turn subwoofer output on or off.
Subwoofer2 (subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to select the phase of subwoofer out-
put.
Normal (normal phase)
—
Reverse (reverse
phase)
3
Push M.C. up or down to adjust the output level
of the subwoofer.
Adjustment range:
+6 to
–
24
4
Push M.C. left or right to select the cut-off fre-
quency.
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
Bass Booster (bass boost)
En
28
Section
03
Operating this unit