Pioneer DVH-P590MP Скачать руководство пользователя

Страница: 1 / 8

Connecting the Units

<ENGLISH>

Note:

•

When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.

•

Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

•

To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a
battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not remove RCA caps if RCA cables are

not used.

— Do not shorten any cables.
— Never cut the insulation of the power cable of

this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.

— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.

•

Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.

•

Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.

•

IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.

•

Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.

•

Cord function may differ according to the
product, even if cord color is the same. When
connecting this system, be sure to check all
manuals and connect cords correctly.

No ACC position

ACC position

ACC

Power cable connection

15 cm

Note:

Depending on the kind of vehicle, the
function of 3* and 5* may be different. In
this case, be sure to connect 2* to 5* and 4*
to 3*.

Connect leads of the same
color to each other.

Cap (1*)
Do not remove cap if
this terminal is not in
use.

Yellow (3*)
Back-up (or
accessory)

Red (5*)
Accessory
(or back-up)

Yellow (2*)
Connect to the constant
12 V supply terminal.

Red (4*)
Connect to terminal controlled
by ignition switch (12 V DC).

ISO connector

Note:

In some vehicles, the ISO connector
may be divided into two. In this case,
be sure to connect to both connectors.

Speaker leads
White: Front

left

White/black: Front left

≠

Gray: Front

right

Gray/black: Front right

≠

Green: Rear

left

or subwoofer

Green/black: Rear left

≠

or subwoofer

≠

Violet: Rear

right

or subwoofer

Violet/black: Rear right

≠

or subwoofer

≠

Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).

Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).

The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.

Notes:

• Change the initial setting of this unit (refer to the

Operation Manual). The subwoofer output of this
unit is monaural.

• When using a subwoofer of 70 W (2

Ω

) , be sure to

connect with Violet and Violet/black leads of this
unit. Do not connect anything with Green and
Green/black leads.

Yellow/black
If you use an equipment with Mute function, wire
this lead to the Audio Mute lead on that equipment.
If not, keep the Audio Mute lead free of any
connections.

Black (chassis ground)
Connect to a clean, paint-free metal location.

This product

Antenna jack

Fuse (10 A)

Fuse resistor

Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).

IP-BUS input
(Blue)

IP-BUS cable

Multi-CD player
(sold separately)

Blue/white (6*)

16 cm

When you connect the separately sold multi-channel
processor (DEQ-P6600) to this unit, do not connect
anything to the speaker leads and system remote
control (blue/white).

Violet/white
Of the two lead wires connected to the back lamp,
connect the one in which the voltage changes when
the gear shift is in the REVERSE (R) position.
For details, refer to

When connecting with a rear view camera

INST

ALLA

TION MANUAL

êìä

éÇé

Ñë
íÇé èé ì

íÄçéÇäÖ

DVH-P590MP

Printed in Thailand

<CRD4222-A/N> RE

This product conforms to new cord colors.