Pioneer DEH-9300SD, Руководство по эксплуатации

Страница: 14 / 28

3 Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
Fader/Balance (fader/balance adjustment)
1
Push M.C. up or down to adjust the front/rear
speaker balance.
!
The front/rear speaker balance cannot be ad-
justed when the rear output setting is
Rear
SP :S/W . Refer to S/W control (rear output
and subwoofer setting) on page 16.
2
Push M.C. left or right to adjust the left/right
speaker balance.
Powerful (equalizer recall)
1
Push M.C. left or right to select an equalizer
curve.
Powerful
—
Natural
—
Vocal
—
Custom1
—
Cus-
tom2
—
Flat
—
Super bass
100 Hz (equalizer adjustment)
You can adjust the currently selected equalizer curve
setting as desired. Adjusted equalizer curve settings
are stored in
Custom1 or Custom2 .
!
A separate Custom1 curve can be created for
each source. If you make adjustments when a
curve other than
Custom2
is selected, the equali-
zer curve settings will be stored in
Custom1
.
!
A
Custom2
curve that is common for all sources
can be created. If you make adjustments when
the
Custom2 curve is selected, the Custom2
curve will be updated.
1
Recall the equalizer curve you want to adjust.
2
Push M.C. left or right to select the equalizer
band to adjust.
100Hz
—
315Hz
—
1.25kHz
—
3.15kHz
—
8kHz
3
Push M.C. up or down to adjust the equalizer
curve.
+6 to
–
6 is displayed as the equalizer curve is in-
creased or decreased.
LOUD (loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press M.C. to turn loudness on or off.
2
Push M.C. left or right to select the desired set-
ting.
Low (low)
—
Mid (mid)
—
High (high)
Sub W.1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output which
can be turned on or off.
1
Press M.C. to turn subwoofer output on or off.
2
Push M.C. left or right to select the phase of sub-
woofer output.
Push
M.C.
left to select reverse phase and
Re-
verse
appears in the display. Push
M.C.
right to
select normal phase and
Normal
appears in the
display.
Sub W.2
(subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Push
M.C.
left or right to select the cut-off fre-
quency.
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
2
Push M.C. up or down to adjust the output level
of the subwoofer.
Each time
M.C. is pushed up or down, subwoofer
level increases or decreases. +6 to -24 is dis-
played as the level is increased or decreased.
Bass (bass boost)
1
Push M.C. up or down to select a desired level.
0 to +6 is displayed as the level is increased or de-
creased.
HPF (high pass filter adjustment)
When you do not want low sounds from the subwoo-
fer output frequency range to play from the front or
rear speakers, turn on the HPF (high pass filter). Only
frequencies higher than those in the selected range
are output from the front or rear speakers.
1
Press
M.C.
to turn high pass filter on or off.
2
Push
M.C.
left or right to select the cut-off fre-
quency.
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
SLA (source level adjustment)
SLA (Source Level Adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!
When selecting FM as the source, you cannot
switch to
SLA .
!
Settings are based on the FM volume level, which
remains unchanged.
!
The MW/LW volume level can also be adjusted
with this function.
1
Push
M.C.
up or down to adjust the source vo-
lume.
Adjustment range:
+4
to
–
4
En
14
Section
02
Operating this unit